Abstract:Chemical recycling of plastic waste via thermochemical processes is essential to move to a carbo-circular economy, reducing our dependence of fossil resources. However, recovering monomers from polyolefins in one or multiple steps is challenging due to their chemical inertness. In the present work, a tandem micro-pyrolyzer coupled to comprehensive two-dimensional gas chromatography and FID/ToF-MS detectors was utilized to study the performance of industrial formulations of steam-treated FCC catalysts and HZSM-5 additives for the in-line catalytic upgrading of polyolefin pyrolysis products towards light olefins and aromatics in two steps. When upgrading pyrolysis vapors from LDPE over the steam-treated catalysts at 600 °C, CH4 yields did not exceed 0.5 wt% due to their low acidity. The FCC catalyst formulations obtained higher yields of C5-C11 aliphatics (up to 42 wt%) and were more active in converting C12 + products than the HZSM-5-containing additives. The highest C2-C4 olefin selectivity of 53 wt% was obtained using a bare steam-treated HZSM-5 additive. With this catalyst, at higher catalyst loading and temperature (700 °C), the light olefin yield reached 69 wt% (19% ethylene, 22% propylene, 10% 1,3-butadiene, and 18% other C4 olefins). Importantly, similar yields of light olefins with even higher propylene yields of 31 wt% were obtained when processing real post-consumer mixed polyolefin waste. An adjusted loading of unsteamed catalyst (to obtain a similar level of initial conversion of C12 + products) showed higher coking propensity and deactivated more rapidly than its steam-treated version. The research results show great potential for the pyrolysis of mixed polyolefin waste followed by the direct in-line upgrading of the pyrolysis vapors to produce high value base chemicals such as C2-C4 olefins, aromatics, and naphtha-range aliphatics at high selectivity while limiting formation of coke, CH4, and H2.

Ni-catalyzed carbon-carbon bonds cleavage of mixed polyolefin plastics waste

Mechanistic Understanding of Efficient Polyethylene Hydrocracking over Two-Dimensional Platinum-Anchored Tungsten Trioxide.

Catalytic Hydrogenolysis of Plastic to Liquid Hydrocarbons over a Nickel-Based Catalyst

Hydrogen-free Upcycling of Polyethylene Waste to Methylated Aromatics over Ni/ZSM-5 under Mild Conditions.

Catalytic conversion of mixed polyolefins under mild atmospheric pressure

Polyethylene Hydrogenolysis over Bimetallic Catalyst with Suppression of Methane Formation

Precise activation of C–C bonds for plastics recycling and upcycling

Micelles Cascade Assembly to Tandem Porous Catalyst for Waste Plastics Upcycling

Hydrogenolysis of Polypropylene and Mixed Polyolefin Plastic Waste over Ru/C to Produce Liquid Alkanes

Temperature-Dependent Nifeal Catalysts for Efficient Microwave-Assisted Catalytic Pyrolysis of Polyethylene into Value-Added Hydrogen and Carbon Nanotubes

Catalytic pyrolysis of film waste over Co/Ni pillared montmorillonites towards H2 production

Maximizing light olefins and aromatics as high value base chemicals via single step catalytic conversion of plastic waste

Cu Promoted the Dynamic Evolution of Ni-Based Catalysts for Polyethylene Terephthalate Plastic Upcycling

Enhancing light fuel production through catalytic pyrolysis of municipal mixed plastic waste over activated spent FCC catalyst

Conversion of Polyolefin Waste to Liquid Alkanes with Ru-Based Catalysts under Mild Conditions

Sustainably Recycling and Upcycling of Single-Use Plastic Wastes Through Heterogeneous Catalysis

Production of C5-C12 olefins by catalytic pyrolysis of low-density polyethylene with MCM-41 in CO2/N2

Photocatalyzing Waste Plastics into C2 Fuels under Simulated Natural Environments.

Polyethylene upcycling to fuels: Narrowing the carbon number distribution in n-alkanes by tandem hydropyrolysis/hydrocracking

One‐pot Hydrogenolysis of Polyethylene Terephthalate (PET) to p‐xylene over CuZn/Al2O3 Catalyst

Photocatalytic Conversion of Waste Plastics into C2 Fuels under Simulated Natural Environment Conditions