Abstract:The warm‐rolled and cryogenically treated sample achieved exceptional mechanical properties, with a yield strength of ≈949 MPa and elongation of ≈56.2%. Its high strength stems from grain refinement, increased dislocation density, and martensite formation via cryogenic treatment. Deformation is stage‐dependent: early dislocation slip, mid‐stage transformation‐induced plasticity (TRIP) effect, and late‐stage martensite slip. Fine grains delay TRIP, enhancing ductility. The austenitic stainless steel undergo warm rolling, followed by cryogenic treatment. The warm‐rolled and cryogenically treated (WR‐CT) sample exhibits superior strength and ductility compared to the warm‐rolled (WR) sample, achieving a yield strength of 949 MPa and an elongation of ≈56.2%. The enhanced strength is attributed to the higher dislocation density, additional grain refinement, and the presence of martensite in the WR‐CT sample. The WR and WR‐CT samples exhibit similar deformation mechanisms. In the initial stage, dislocation slip predominantly governs the deformation. During the intermediate stage, the transformation‐induced plasticity (TRIP) effect dominates the deformation mechanism. In the final stage, nearly all austenite transforms into martensite, and deformation mainly occurs via dislocation slip within the martensite phase. However, in the WR‐CT sample, the TRIP effect is delayed during the stable processing stage (≈8–23%) due to the higher mechanical stability of austenite, resulting from further grain refinement and higher dislocation density. Additionally, the coordinated deformation of strain‐induced martensite with varying orientations contributes to delayed necking, achieving an optimal balance between strength and ductility.

A Novel Multiphase Stainless Steel with Ultra-Low Yield Ratio and High Ductility

Light-weight Isometric-Phase Steels with Superior Strength-Hardness-ductility Combination

Design of Tri-Phase Lamellar Architectures for Enhanced Ductility in Ultra-Strong Steel

A Novel Cast Multiphase Stainless Steel with High Strength and High Toughness

Enhancing Strength and Plasticity Synergy in Transformation-Induced Plasticity-Aided Lean Duplex Stainless Steel Based on the Ultrafine-Grained Austenite

Mechanical properties and deformation mechanisms of a novel austenite-martensite dual phase steel

Ensuring the strength and ductility synergy in an austenitic stainless steel: single- or multi-phase hetero-structures design

A cryogenic ultra-strong and ductile steel induced by stable nanoscale dual-phase structure

Nature-Inspired Hierarchical Steels.

Achieving Excellent Strength–Ductility Synergy by Tailoring the Grain Size Distribution in a Metastable Austenitic Stainless Steel

Achieving Unexpected Strength and Ductility Synergies in Heterogeneous Metastable Lamellar Steels

Microstructure and Mechanical Properties of a Novel Cast Multi-Phase Stainless Steel

Strain partitioning in ferrite and mechanical properties of a cast multiphase stainless steel

Microstructure and mechanical properties of a cast TRIP-assisted multiphase stainless steel

Mechanisms of strength–plasticity enhancement and stress-induced phase transition in a medium-carbon low-alloy steel

Novel 1.5 GPa-strength with 50%-ductility by transformation-induced plasticity of non-recrystallized austenite in duplex steels

Attainment of an exceptionally high strength in low-carbon steel along with modest ductility through a novel heat treatment route

Discovery of a novel low-cost medium-entropy stainless steel with exceptional mechanical behavior over a wide temperature range

Enhanced strength and ductility of the low-carbon steel with heterogeneous lamellar dual-phase structure produced by cyclic intercritical rolling

Strength‐Ductility Synergy in an Austenitic Stainless Steel Processed by Warm Rolling and Subsequent Cryogenic Treatment

Superior fracture toughness in a high-strength austenitic steel with heterogeneous lamellar microstructure