Abstract:Main text The objective of the Supplementary Comparison (SC) SIM.M.FF-S9 for water flow measurement was to support and prove the Calibration and Measurement Capabilities (CMC) of the participating NMIs of Chile (CISA), Peru (INACAL), Bolivia (IBMETRO) and Argentina (INTI). As pilot laboratories, the national metrology institutes of Germany (PTB) and CENAM (Mexico) supported the comparison with reference values. The comparison was organized as a single round robin, started in January 2016 at PTB and finished in August 2019, also at PTB. A combined setup of a turbine meter and Coriolis meter was used as a transfer standard. The nominal calibration conditions of the SC were defined in the flow range between 10 m 3 /h and 130 m 3 /h, 20 °C fluid temperature and 0.3 MPa line pressure. In order to estimate the uncertainties u TS , both transfer meters were subjected to extensive characterization measurements at pilot laboratory PTB. The following parameters were researched in detail: fluid temperature, line pressure, reproducibility, flow stability and meter sensitivity to different inflow conditions. The E N values for the turbine meter were calculated based on PTB data, only. The E N values for the Coriolis meter are partly linked to Key Comparison CCM.FF-K1.2015 and were calculated using a common reference value of PTB and CENAM data. The uncertainty of turbine meter u TS was clearly dominated by the sensitivity to disturbed inflow conditions which leads to large values of u TS with > 0.20 %. Beside one calibration, all labs passed the E N criteria of ≤ 1.20. But, due to large values of u TS , the calibrations for all labs were evaluated as inconclusive. The evaluation criteria u comp /u base exceeded the critical value of 2.00 for all calibrations. Finally, the turbine meter was not suitable for a confirmation of the submitted CMC values. The calibration results of the Coriolis meter were characterized by a strong dependency on zero setting. The observed effect was adjusted for the data of both reference laboratories by introducing a new method for autozero correction. Maximum uncertainty values for Coriolis u TS were estimated with 0.069 % at low flowrates and 0.033 % at high flowrates. Besides two calibrations, all laboratories complied with the E N criteria of ≤ 1.20. In contrast to turbine meter, the evaluation criteria u comp /u base exceeded the critical value of 2.00 at one calibration, only. In consequence, the calibrations by using the Coriolis meter were suitable for a confirmation of the submitted CMC values. In summary, the comparison was successfully finished for a confirmation of the submitted CMC values, related to mass calibrations. For volume related CMCs this comparison was not suitable. The comparison was partially financially supported by the German Federal Ministry for Economic Cooperation and Development (BMZ) - PNs: 2012.2296.7-95259, 2015.2037.8-95306 and 2017.2073.9-95328. To reach the main text of this paper, click on Final Report. Note that this text is that which appears in Appendix B of the BIPM key comparison database https://www.bipm.org/kcdb/. The final report has been peer-reviewed and approved for publication by the CCM, according to the provisions of the CIPM Mutual Recognition Arrangement (CIPM MRA).

Supplementary comparisons of DC high voltage measuring reference instruments COOMET 449Ru-a08 (COOMET_EM-S7)

Supplementary comparisons of reference measuring systems of electric capacitance and loss dissipation factor on AC high voltage of power frequency COOMET 604/RU-a/13 (COOMET.EM-S18)

COOMET key comparison COOMET.PR-K1.a.2018 for spectral irradiance 250 nm to 2500 nmm, final report

Supplementary comparison of national measurement standards of gauge pressure in the range from 1 MPa to 10 MPa

Bilateral comparison of 1.018 V and 10 V standards between INRIM (Italy) and the BIPM, November to December 2023 (part of the ongoing BIPM key comparison BIPM.EM-K11.a and b)

Bilateral comparison of 1.018 V and 10 V standards between SASO-NMCC (Saudi Arabia) and the BIPM, September to November 2023 (part of the ongoing BIPM key comparison BIPM.EM-K11.a and b)

EURAMET.EM.RF-S46 (EURAMET Project No 1538) EURAMET supplementary comparison on magnetic field strength measurements for frequencies up to 30 MHz

Supplementary comparison on a platinum resistance thermometer calibration from -70 °C to 250 °C

Supplementary comparison SIM.M.FF-S9.2016 for water flow measurement

Bilateral Comparison of 1.018 V and 10 V Standards Between the KRISS (republic of Korea) and the BIPM, February 2008 (part of the Ongoing BIPM Key Comparison BIPM.EM-K11.a and B)

KEY COMPARISON: CCQM-K34 Final Report: Assay of Potassium Hydrogen Phthalate

CCM.G-K2 key comparison

Final report for CCT comparison of ITS-90 realisations above the silver point using two transfer radiation thermometers and a set of high temperature fixed-point blackbody cells

CCEM key comparison CCEM.RF-K26. Attenuation at 18 GHz, 26.5 GHz and 40 GHz using a step attenuator. Final report of the pilot laboratory

CCQM-K173.1 - Assay of sodium carbonate. Final report

Final report, ongoing key comparison BIPM.QM-K1, ozone at ambient level, comparison with CMS/ITRI, March 2024

EURAMET.T-K9 regional key comparison ITS-90 SPRT calibration from the Ar TP to the Zn FP

Linkage for Metrosert to CCT-K9 via the EURAMET-T.K9.1 bilateral comparison

SIM Thermocouple Type S Supplementary Comparison

Final report on supplementary comparison of national standards in the field of flow and mass of liquid within the flow range of 0.1 t/h to 45 t/h

EURAMET Key Comparison EURAMET.M.D-K4.2020: Hydrometer Calibration Comparison from 600 Kg/m3 to 2000 Kg/m3