Abstract:This research investigates stress evolution and plastic deformation characteristics influencing particle–matrix interface decohesion in AA7075-O aluminum sheets. Employing a combined molecular dynamics (MD) - finite element (FE) approach, three interfaces (Al-η, Al-θ, Al-Fe-rich intermetallic) are studied under various loading conditions. Cohesive properties, represented by traction-separation (T-S) curves, are derived using a novel methodology from MD simulations to estimate critical peak traction ( t ) initiating decohesion and the work of separation ( G ) at quasistatic strain rates. It is shown that all three interfaces are weaker in shear than in normal loading. The cohesive property estimates from MD simulations are utilized as input in FE-based models with both real and simplified microstructures of AA7075-O sheet material. These models are subjected to large plastic strains, and the decohesion behavior of each particle type are analyzed. It is shown that particle decohesion is a function of inherent cohesive properties, local inter-particle alignment with respect to loading direction, particle morphology and particle size. Interparticle alignment between 0 and 45 degree promote particle decohesion. Larger sized particles with smaller dimensions along loading direction aid early decohesion of particles. Decohesion of a particle can also facilitate debonding of neighbouring particles under continued loading. Fe-rich particles have higher likelihood for decohesion due to their weaker interface. The θ precipitates, despite having comparable interface strength as η particles, manifest a tenfold increase in susceptibility to decohesion due to the effect of particle morphology and size.

Immersed nano-sized Al dispersoids in an Al matrix; effects on the structural and mechanical properties by Molecular Dynamics simulations

Atomistic Simulations of Basal Dislocations Interacting with Mg$_{17}$Al$_{12}$ Precipitates in Mg

Quantitative analysis of influence of α-Al(MnFeCr)Si dispersoids on hot deformation and microstructural evolution of Al-Mg-Si alloys

Size Dependence and Stochastic Nature of Yield Strength of Micron-Sized Crystals: a Case Study on Ni3Al

Understanding Homogeneous Nucleation in Solidification of Aluminum by Molecular Dynamics Simulations

Multi-scale modeling of decohesion characteristics of second phase particles from the matrix in uniaxial tension in a high strength aluminum alloy

Interdiffusion cross-high-entropy alloys, nano-multilayer foils, and Al interface: An atomistic simulation

The Interaction Mechanisms Between Dislocations and Nano-Precipitates in CuFe Alloys: a Molecular Dynamic Simulation

Enhancing Mechanical Properties of Graphene/Aluminum Nanocomposites via Microstructure Design Using Molecular Dynamics Simulations

Modeling of surface phenomena of liquid Al-Ni alloys using molecular dynamics

Atomistic insights into cluster strengthening in aluminum alloys

An experimentally validated dislocation density based computational framework for predicting microstructural evolution in cold spray process

Investigations of the Mechanical Properties of Nanoimprinted Amorphous Ni–Zr Alloys Utilizing the Molecular Dynamics Simulation

Study of the effects of grain size on the mechanical properties of nanocrystalline copper using molecular dynamics simulation with initial realistic samples

Characterization of Zr-Containing Dispersoids in Al–Zn–Mg–Cu Alloys by Small-Angle Scattering

Atomic-scale deformation mechanisms of nano-polycrystalline Cu/Al layered composites: a molecular dynamics simulation

Atomistic study of hardening mechanism in Al-Cu nanostructure

Diverse yielding regimes of two Mg-Al composite structures predicted by molecular dynamics simulations

Nanomechanical Properties of Imprinted Amorphous NiAl Alloys Using Atomic Simulations

Molecular dynamics investigations of the size effects on mechanical properties and deformation mechanism of amorphous and monocrystalline composite AlFeNiCrCu high-entropy alloy nanowires

Optimizing size and number‐density of Al3Zr dispersoids in Al‐Zn‐Mg‐Cu alloys