Abstract:Abstract During the hydraulic fracturing process, the created rough fracture surface and fracturing fluids with high viscosity greatly challenge proppants placement in the thin aperture of fractures. Thus, it is essential to detailly investigate the effect of surface roughness on the proppant distribution. In addition, the multiphase flow in the rough nanoscale microfractures in the variety of orientations have not been cleared. Taking all of these into consideration; rock grain geometries, packing mechanisms, the presence of clay content, and in-situ stress field will be affected and will affect the presence of the microcracks, and consequently control the permeability and porosity of the sedimentary rock. In the failed rock after fracturing work, a processed zone where the pre-existing natural fractures get activated, and induced microcracks including intergranular and intragranular grain boundaries are brought to connect to the main fracture. Hence, the rock grain and pore size distributions at fracture processed zone are altered. This, in turn, controls the fluid transport in the rocks. Our novel approach incorporates the image analysis software (ImageJ) by organizing desired image processing codes to study the critical features of the post-fracturing core sample, including main fracture roughness, mechanical rock properties, crack density, grain, and pore size distributions. Tennessee sandstone was undergone the hydraulic fracturing test and polished on a cross-section perpendicular to the main fracture. This cross-section was recorded by the high-resolution SEM images after ion-milling. Corresponding grain size and pore size distributions are studied at each representative location with respect to its distance to the main fracture to probe alterations of the fracturing process from the core sample original state. The results of grain size and pore size distributions are compared. The discussions of their alterations mechanisms and their effects on the rock porosity and permeability are analyzed. We find that the roughness presence of fractures strongly increases conduits open to fluid flow. In addition, our developed image processing code perfectly captured the rock grains with the promising precision. Further, we are able to observe the grain size deduction due to the incremental intragranular grain boundaries while intergranular grain boundaries are still majorities outside the fracture processed zone (FPZ). Grain size renders a lognormal distribution at each representative location and coincides with the permeability distribution of most reservoir rocks. Grain size averages also match the literature values with reasonable uncertainties (20%). The pore size distribution and its average value vary spatially. Results from this study kindle the insights of the heterogeneity of the fractured formation with proper petrophysics parameters quantitatively. We also found that the aspect ratio from 2D image analysis does not reflect the significance in the mechanics. This novel approach will commit to supporting the lab measurements, gives field preliminary hydraulic fracturing performance assessment and lower the cost needed for hydraulic fracturing design.

High resolution, non-destructive measurement and characterization of fracture apertures

Effect of Shear-Induced Aperture Evolution on Fluid Flow in Rock Fractures

Estimation of Fracture Permeability from Aperture Distributions for Rough and Partially Cemented Fractures

Aperture measurements and seepage properties of typical single natural fractures

Fracture aperture and fill characterization in a limestone quarry using GPR thin-layer AVA analysis

The frequency and apertures of fractures in rock

Laboratory Simulation of Flow Through Rough-Walled Microfractures under High Hydraulic Gradient

Relating Hydro‐Mechanical and Elastodynamic Properties of Dynamically Stressed Tensile‐Fractured Rock in Relation to Applied Normal Stress, Fracture Aperture, and Contact Area

Modeling the impact of natural roughness of tension joints on heat transport

Characterization of fracture aperture field heterogeneity by electrical resistance measurement

Quantification of Fracture Roughness and its Effects on the Grain and Pore Size Distribution of the Fractured Rock Using Image Analysis Technique

Descriptive and quantitative analysis of fracture systems in a carbonate rock mass complex

Size Effect on Hydraulic Properties of Rough-Walled Fractures Upscaled from Meter-Scale Granite Fractures

Measurement of Hydraulic Fracture Aperture by Electromagnetic Induction

Identification of solute transport parameters in fractured granites with heterogeneous apertures

Automatic and time-resolved determination of fracture characteristics from in situ experiments

Study on Flow and Heat Transfer in Single Rock Fractures for Geothermal Heat Extraction

Estimation of Effective Fracture Aperture in Glacial Tills by Analysis of Dye Tracer Penetration

Characterization methods for natural fractures distribution in shale and tight reservoirs

A geometrical aperture-width relationship for rock fractures

The roughness of fracture surfaces and its scale dependence – a methodological study based on natural fractures in sandstones from Southern Germany