MgB2 synthesis in closed volume and pinning potential

S.P. Ananev,V.A. Grinenko,V.A. Keilin,E.P. Krasnoperov,P.A. Levit,V.A. Stoliarov

DOI: https://doi.org/10.48550/arXiv.cond-mat/0210317

2002-10-15

Abstract:Superconducting MgB2 was synthesized in a stainless steel tube which compressed by pulsed magnetic field. The temperature dependence of diamagnetic moment m(T) was investigated and the pinning potential was determined

Superconductivity

What problem does this paper attempt to address?

Pinning Mechanism in Carbon Nanotube Doping of Mgb2 Superconductor

GQ Yuan,XN Xu,ZH Wang,DW Lu,X Jin

DOI: https://doi.org/10.1016/j.ssc.2005.05.023

IF: 1.934

2005-01-01

Solid State Communications

Abstract:MgB1.9C0.1 samples are synthesized under the ambient pressure (AP) and high pressure (HP), respectively. The further studies demonstrate different field-dependence of the critical current density Jc(H) in each sample. In the view of two-gap superconductivity in these samples, δTc pinning (resulting from the spatial fluctuations of the transition temperature) is dominant in the AP sample, while in the HP sample, both δTc and δl pinning (due to the mean-free-path fluctuations) act together and their contributions vary with temperature. Besides the improvement of Hc2(0), due to the different pinning mechanism, Jc(H) of the HP sample shows a slower decay with the increasing fields than that of the AP sample in high fields, which suggests a possible method of retarding the rapid decay of Jc(H) under elevated fields.
The mechanism of pore formation in superconducting MgB2 synthesized at low temperature by in-situ process

Yifang Wu,Guo Yan,Shicheng Yan,Chengshan Li,Jinshan Li,Yafeng Lü

DOI: https://doi.org/10.3321/j.issn:1002-185x.2009.04.018

2009-01-01

Rare Metal Materials and Engineering

Abstract:Using X-ray diffraction (XRD), scanning electron microscopy (SEM) and differential scanning calorimetry (DSC) the mechanism of pore formation of superconducting MgB2 synthesized at low temperature by in-situ process was studied. It is showed that B powder was embedded into Mg powder after the ball-milling process. MgB2 phase formed firstly in these embedded areas. The closed pores in MgB2 bulks are caused by kirkendall effect due to the different diffusion speeds of Mg and B atoms. The open pores are caused by Mg gas.
Properties of superconducting MgB_2 wires: "in-situ" versus "ex-situ" reaction technique

Alexey V Pan,Sihai Zhou,Huakun Liu,Shixue Dou

DOI: https://doi.org/10.1088/0953-2048/16/5/317

2003-02-13

Abstract:We have fabricated a series of iron-sheathed superconducting wires prepared by the powder-in-tube technique from (MgB_2)_{1-x}:(Mg+2B)_x initial powder mixtures taken with different proportions, so that x varies from 0 to 1. It turned out that "ex-situ" prepared wire (x = 0) has considerable disadvantages compared to all the other wires in which "in-situ" assisted (0 < x < 1) or pure "in-situ" (x = 1) preparation was used due to weaker inter-grain connectivity. As a result, higher critical current densities J_c were measured over the entire range of applied magnetic fields B_a for all the samples with x > 0. Pinning of vortices in MgB_2 wires is shown to be due to grain boundaries. J_c(B_a) behavior is governed by an interplay between the transparency of grain boundaries and the amount of "pinning" grain boundaries. Differences between thermo-magnetic flux-jump instabilities in the samples and a possible threat to practical applications are also discussed.

Superconductivity
Fabrication and Superconducting Properties of MgB2 Wires with Amorphous Carbon Doping by In-situ Powder-in-tube Method

Guo YAN,Qingyang WANG,Guoqing LIU,Huan YANG,Chengshan LI,Yafeng LU,Haihu WEN

DOI: https://doi.org/10.3321/j.issn:1000-7857.2008.01.006

2008-01-01

Abstract:Amorphous carbon-doped MgB2/Nb/Cu wires were fabricated by in-situ powder-in-tube method. The samples were characterized using scanning electron microscope, standard four probe technique and magnetometer. It is found that amorphous carbon doping decreases the critical temperature of MgB2/Nb/Cu wires but significantly improves the critical field and critical current density. The irreversibility field of the wire sintered at 750℃ reaches 5.2 T at 20 K. The results show a good prospect in fabricating high performance MgB2 wires by in-situ PIT method.
Superconducting Properties of MgB 2 Prepared by High Pressure and Ambient Pressure

ZA Ren,GC Che,ZX Zhao,H Chen,C Dong,YM Ni,SL Jia,HH Wen

DOI: https://doi.org/10.1088/0256-307x/18/4/342

2001-01-01

Chinese Physics Letters

Abstract:The new superconductor MgB2 has been prepared in two ways, by high pressure and ambient pressure synthesis. The superconducting properties were measured and compared. It is found that the sample prepared by high pressure is much denser than that prepared under ambient pressure. Accordingly the high pressure sample has a very narrow transition width and a much higher bulk critical current density.
High-Pressure Synthesis of Mgb2 Superconductor with T-C above 39 K

SC Li,JL Zhu,RC Yu,FY Li,ZX Liu,CQ Jin

DOI: https://doi.org/10.1088/1009-1963/10/4/315

2001-01-01

Chinese Physics

Abstract:We report on the high-pressure synthesis and superconductivity of MgB2 intermetallic compounds. The compounds have been obtained through high-pressure sintering of the mixtures of magnesium and boron fine powders under 5.0 GPa and at similar to 1000 degreesC for 30 min. Magnetic measurements using a SQUID magnetometer show the sharp bulk superconducting transition above 39 K; the four-probe de resistivity measurements indicate the highly-conductive normal state and sharp superconducting transition. The results highlight that high-pressure synthesis would be a promising way to promote the studies of this new kind of intermetallic superconductors.
Significant Enhancement of Flux Pinning in Mgb2 Superconductor Through Nano-Si Addition

XL Wang,SH Zhou,MJ Qin,PR Munroe,S Soltanian,HK Liu,SX Dou

DOI: https://doi.org/10.1016/s0921-4534(02)02813-7

2003-01-01

Abstract:Polycrystalline MgB2 samples with 10 wt.% silicon powder addition were prepared by an in situ reaction process. Two different Si powders, one with coarse (44 mum) and the other with nano-size (<100 nm) particles were used for making samples. The phases, microstructures, and flux pinning were characterized by XRD, TEM, and magnetic measurements. It was observed that the samples doped with nano-sized Si powder showed a significantly improved field dependence of the critical current over a wide temperature range compared with both undoped samples and samples with coarse-Si added. J(c) is as high as 3000 A/cm(2) in 8 T at 5 K, one order of magnitude higher than for the undoped MgB2. X-ray diffraction results indicated that Si had reacted with Mg to form Mg2Si. Nano-particle inclusions and substitution, both observed by transmission electron microscopy, are proposed to be responsible for the enhancement of flux pinning in high fields. However, the samples made with the coarse-Si powders had a poorer pinning than the undoped MgB2 (C) 2002 Elsevier Science B.V. All rights reserved.
Superconducting properties of the powder-in-tube Cu-Mg-B and Ag-Mg-B wires

B. A. Glowacki,M. Majoros,M. E. Vickers,B. Zeimetz

DOI: https://doi.org/10.1016/S0921-4534%2802%2900986-3

2001-09-05

Abstract:The new class of Mg-B superconducting conductors was prepared using the standard in-situ powder-in-tube, PIT, method where Mg+2B mixture was used to fill the copper and silver tubes. Study of the intergranular current, grain connectivity and superconducting phases in wires were conducted by AC susceptibility measurements and direct four point transport measurements. Using SQUID magnetometer, magnetisation versus magnetic field (M-H) curves of the round wires after reactive diffusion were measured at temperatures 5K and magnetic field up to 5T to define the Jcmag . The direct current density measurements of the in-situ Cu-MgB2 performed at 4.2K gave the value of 10^9 Am-2 .

Superconductivity,Materials Science
Superconducting anisotropy and evidence for intrinsic pinning in single crystalline MgB$_2$

Ken'ichi Takahashi,Toshiyuki Atsumi,Nariaki Yamamoto,Mingxiang Xu,Hideaki Kitazawa,Takekazu Ishida

DOI: https://doi.org/10.1103/PhysRevB.66.012501

2002-05-01

Abstract:We examine the superconducting anisotropy $\gamma_c = (m_c / m_{ab})^{1/2}$ of a metallic high-$T_c$ superconductor MgB$_2$ by measuring the magnetic torque of a single crystal. The anisotropy $\gamma_c$ does not depend sensitively on the applied magnetic field at 10 K. We obtain the anisotropy parameter $\gamma_c = 4.31 \pm 0.14$. The torque curve shows the sharp hysteresis peak when the field is applied parallel to the boron layers. This comes from the intrinsic pinning and is experimental evidence for the occurrence of superconductivity in the boron layers.

Superconductivity
Scanning Hall Probe Microscopy of Unconventional Vortex Patterns in the Two-Gap MgB2superconductor

J. Gutierrez,B. Raes,A. V. Silhanek,L. J. Li,N. D. Zhigadlo,J. Karpinski,J. Tempere,V. V. Moshchalkov

DOI: https://doi.org/10.1103/physrevb.85.094511

2012-01-01

Abstract:The low magnetic field vortex patterns nucleation and evolution in a high-quality two-gap superconductor MgB2 single crystal have been investigated by low-temperature scanning Hall probe microscopy. Large areas have been imaged with single-vortex resolution while changing systematically the thermodynamic parameters for field and temperature. The obtained patterns have been studied and compared with those of a reference 2H-NbSe2 single crystal. We found that the observed vortex patterns in MgB2 (e.g., stripes, clusters) appear due to competing vortex-vortex interactions as suggested by the theory of type-1.5 superconductivity.
Intra-granular Ti precipitates in MgB2

M. J. Kramer,S. L. Bud'ko,P. C. Canfield,R. H. T. Wilke,D. K. Finnemore,R. J. Suplinskas,M.J. Kramer,S.L. Bud'ko,P.C. Canfield,R.H.T. Wilke,D.K. Finnemore,R.J. Suplinskas

DOI: https://doi.org/10.48550/arXiv.cond-mat/0302443

2003-02-21

Superconductivity

Abstract:Superconducting magnesium diboride has been prepared with intra-granular TiB precipitates that have appropriate size and spacing for the pinning of superconducting vortices. The TiB particles have a size ranging from 1 nm to 20 nm and a spacing about 5 times as large. By co-depositing Ti and B on a commercial carbon coated silicon carbide substrate with chemical vapor deposition methods, it was possible to obtain a starting fiber with Ti well dispersed in the B. Reacting these fibers in a Mg vapor then transformed the fiber into a superconductor capable of carrying 10,000 A/cm^2 at 25K and 1 T. The Ti-B bonds are strong enough that there is relatively little migration of the Ti as the MgB2 grains form around the TiB precipitates. TiB2 precipitates, if they are present, can not be seen in the selected area diffraction pictures that show the TiB precipitates.
Investigation of Layered Structure Formation in MgB2 Wires Produced by the Internal Mg Coating Process under Low and High Isostatic Pressures

Daniel Gajda,Michał Babij,Andrzej Zaleski,Doğan Avci,Fırat Karaboga,Hakan Yetis,Ibrahim Belenli,Tomasz Czujko

DOI: https://doi.org/10.3390/ma17061362

IF: 3.4

2024-03-16

Materials

Abstract:Currently, MgB2 wires made by the powder-in-tube (PIT) method are most often used in the construction and design of superconducting devices. In this work, we investigated the impact of heat treatment under both low and high isostatic pressures on the formation of a layered structure in PIT MgB2 wires manufactured using the Mg coating method. The microstructure, chemical composition, and density of the obtained superconductive wires were investigated using scanning electron microscopy (SEM) with an energy-dispersive X-ray spectroscopy (EDS) analyzer and optical microscopy with Kameram CMOS software (version 2.11.5.6). Transport measurements of critical parameters were made by using the Physical Property Measurement System (PPMS) for 100 mA and 19 Hz in a perpendicular magnetic field. We observed that the Mg coating method can significantly reduce the reactions of B with the Fe sheath. Moreover, the shape, uniformity, and continuity of the layered structure (cracks, gaps) depend on the homogeneity of the B layer before the synthesis reaction. Additionally, the formation of a layered structure depends on the annealing temperature (for Mg in the liquid or solid-state), isostatic pressure, type of boron, and density of layer B before the synthesis reaction.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Substitution induced pinning in MgB_2 superconductor doped with SiC nano-particles

S. X. Dou,A. V. Pan,S. Zhou,M. Ionescu,H. K. Liu,P. R. Munroe

DOI: https://doi.org/10.1088/0953-2048/15/11/317

2002-06-24

Abstract:By doping MgB_2 superconductor with SiC nano-particles, we have successfully introduced pinning sites directly into the crystal lattice of MgB_2 grains (intra-grain pinning). It became possible due to the combination of counter-balanced Si and C co-substitution for B, leading to a large number of intra-granular dislocations and the dispersed nano-size impurities induced by the substitution. The magnetic field dependence of the critical current density was significantly improved in a wide temperature range, whereas the transition temperature in the sample MgB_2(SiC)_x having x = 0.34, the highest doping level prepared, dropped only by 2.6 K.

Superconductivity
Enhanced flux pinning by magnetic CrB2 nanoparticle in MgB2 superconductor

Yutong Liu,Jiajia Qin,Chuan Ke,Cuihua Cheng,Dajin Zhou,Yong Zhang,Yong Zhao

DOI: https://doi.org/10.1016/j.jmmm.2022.169174

IF: 3.097

2022-06-01

Journal of Magnetism and Magnetic Materials

Abstract:Different from the non-magnetic pinning centers, the magnetic pinning centers have stronger flux pinning force due to the direct magnetic interaction between the magnetic pinning centers and the magnetic vortices, thus have been widely used to enhance the critical current density of various superconductors. In this article, nanoparticles of antiferromagnet CrB2 were introduced as magnetic pinning center to improve the flux pinning force density (F p), irreversible field (H irr), and critical current density (J c) of MgB2. Compared to the pristine sample, the CrB2 doped MgB2 with low doping levels shows a significantly improved J c and F p, especially in the high field region. H irr is also substantially enhanced. It is revealed that the magnetic flux pinning behavior of CrB2 doped samples obviously deviates from the surface pinning law followed by most pure MgB2. Through theoretical analysis and curve fitting, an extra pinning force superimposed on the surface pinning background is separated and identified, which follows the rule of point pinning. Such a pinning scenario is supported by the microstructure analyses which demonstrate that CrB2 nanoparticles are highly dispersed and embedded in MgB2 matrix, acting as effective pinning centers.

materials science, multidisciplinary,physics, condensed matter
Improved superconducting properties of MgB2

N. A. Frederick,Shi Li,M. B. Maple,V. F. Nesterenko,S. S. Indrakanti

DOI: https://doi.org/10.1016/S0921-4534%2801%2900948-0

2001-06-26

Abstract:We present electrical transport, magnetization, and specific heat measurements on bulk MgB2 samples (T_{c} = 38.5 K) synthesized under 200 MPa pressure using a process based on hot isostatic pressing with cooling under pressure. The samples are fully dense and display excellent superconducting properties, including a narrow superconducting transition width (\Delta T_{c} = 0.75 K), a high upper critical field H_{c2} (H_{c2}(0) ~ 155 kOe), and a critical current density J_{c} that is the largest yet measured for bulk samples of MgB2 (J_{c}(0) ~ 1.4 MA/cm^{2}). Specific heat measurements yielded a jump \Delta C at T_{c} of 92 mJ/mol K. These superconducting properties are comparable to those obtained with techniques that are not so well suited to industrial scale fabrication.

Superconductivity
High Critical Current Density of a MgB 2 Bulk Superconductor High-pressure Synthesized Directly from the Elements

C-Q. Jin,S-C. Li,J-L. Zhu,F-Y. Li,Z-X. Liu,R-C. Yu

DOI: https://doi.org/10.1557/JMR.2002.0073

IF: 2.7

2002-01-01

Journal of Materials Research

Abstract:We report the property studies of a MgB 2 superconductor with high critical current density. The MgB 2 superconductor was readily fabricated through a direct high-pressure synthesis of the respective elements. The obtained high-density MgB 2 undergoes a sharp superconducting transition at 39 K. The bulk critical current density ( J c ) of the sample was calculated on the basis of Bean’s critical state model, and rather high critical current densities over a wide temperature range were obtained in comparison with the ambient prepared samples. The results highlight that high-pressure sintering would be a promising way to produce and search for this kind of intermetallic boride and the related superconductors.
Superconductivity in porous MgB2

V.A.Grinenko,E.P.Krasnoperov,V.A.Stoliarov,A.A.Bush,B.P.Mikhajlov

DOI: https://doi.org/10.1016/j.ssc.2006.03.036

2006-03-29

Abstract:Porous magnesium diboride samples have been prepared by the heat treatment of a pressed mixture of Mg and MgB2 powders. It was found that linked superconducting structure is formed down to the minimum normalized density gamma= d/do= 0.16 (percolation threshold), where d is the density of MgB2 averaged over the sample, do= 2.62 g/cm3 is the X-ray density. Lattice parameters and critical temperature of the porous sample decrease with increasing porosity (decreasing gamma) and Tc2= 32K is minimal at gamma= 0.16. The grain boundaries in the porous samples are transparent for the current and Jc~3.105A/cm2 in self field at T= 20K in the samples with gamma~ 0.24.

Superconductivity
FABRICATION AND CHARACTERIZATION OF MgB_2/Fe BY EX-SITU PIT METHOD

Wang Dong-Liang,Zhang Xian-Ping,Gao Zhao-Shun,Yu Zheng-Guang,Ma Yan-Wei,Wen Hai-Hu,Guo Jian-Dong

2007-01-01

Abstract:The MgB2/Fe superconducting wires were fabricated by the ex-situ Powder-In-Tube (PIT) process. The samples were characterized using X-ray diffraction, scanning electron microscope, superconducting quantum interference device magnetometer etc. The Jc and its magnetic field dependence were evaluated by a standard four-probe technique. It is found that the critical transition temperature of the superconductor was about 38.3K,and the Jc value was ～104 A/cm2 (4.2 K, 4 T). The high temperature heat-treatment could effectively reduce the stress produced by cold deformation process, and improve the grain connection and the density of the superconducting wire, thus the Jc of the ex-situ wire was enhanced significantly.
High-Temperature Synthesis of Superconducting MgB2 Materials in a Centrifuge

Sanat Tolendiuly,Jaafar Nur-Akasyah,Sergey Fomenko,Ahmet Turan,Sharafhan Assylkhan,Aigul Abisheva

DOI: https://doi.org/10.3390/jcs8070267

2024-07-11

Journal of Composites Science

Abstract:There is a wide variety of superconducting materials, but only a few of them are suitable for practical industrial use, and one of the most promising superconductors is MgB2. Its main advantages are a critical temperature close to 40 K, which allows for operation in a cryogenic environment, low cost of precursors, and the ease of manufacture. In this paper, we attempted to obtain superconducting materials based on magnesium diboride in a new way by using a high-temperature centrifuge and then investigated how centrifugal acceleration could affect the superconducting characteristics of the materials in a greater way during combustion synthesis. As a brief result of this research, it was found that the value of centrifugal acceleration affected the critical current density (Jc = 1.4 A/cm2) of the MgB2 composites, although it did not considerably impact the critical transition temperature of the MgB2 materials (remained at around 37.5–38 K).
Superconducting properties of nanocrystalline MgB$_2$

B Lorenz,O Perner,J Eckert,C W Chu

DOI: https://doi.org/10.48550/arXiv.cond-mat/0607578

2006-07-22

Superconductivity

Abstract:Nanocrystalline MgB$_2$ produced by mechanical alloying has been shown to exhibit enhanced superconducting properties such as increased pinning and higher critical currents. However, the effects of the synthesis process on the intrinsic superconducting properties have not been addressed yet. We have investigated the superconducting gap structure of nanocrystalline MgB$_2$ pellets synthesized by high-energy ball milling employing specific heat measurements. We found that the larger $\sigma$-gap decreased whereas the smaller $\pi$-gap slightly increased in ball milled MgB$_2$ as compared to bulk samples synthesized along the standard routes. The data show that the ball milling process introduces defects that enhance the interband scattering similar to irradiation with neutrons. The reduction of the $\sigma$-gap explains the lower superconducting transition temperature of 33 K.

MgB2 synthesis in closed volume and pinning potential

Pinning Mechanism in Carbon Nanotube Doping of Mgb2 Superconductor

The mechanism of pore formation in superconducting MgB2 synthesized at low temperature by in-situ process

Properties of superconducting MgB_2 wires: "in-situ" versus "ex-situ" reaction technique

Fabrication and Superconducting Properties of MgB2 Wires with Amorphous Carbon Doping by In-situ Powder-in-tube Method

Superconducting Properties of MgB 2 Prepared by High Pressure and Ambient Pressure

High-Pressure Synthesis of Mgb2 Superconductor with T-C above 39 K

Significant Enhancement of Flux Pinning in Mgb2 Superconductor Through Nano-Si Addition

Superconducting properties of the powder-in-tube Cu-Mg-B and Ag-Mg-B wires

Superconducting anisotropy and evidence for intrinsic pinning in single crystalline MgB$_2$

Scanning Hall Probe Microscopy of Unconventional Vortex Patterns in the Two-Gap MgB2superconductor

Intra-granular Ti precipitates in MgB2

Investigation of Layered Structure Formation in MgB2 Wires Produced by the Internal Mg Coating Process under Low and High Isostatic Pressures

Substitution induced pinning in MgB_2 superconductor doped with SiC nano-particles

Enhanced flux pinning by magnetic CrB2 nanoparticle in MgB2 superconductor

Improved superconducting properties of MgB2

High Critical Current Density of a MgB 2 Bulk Superconductor High-pressure Synthesized Directly from the Elements

Superconductivity in porous MgB2

FABRICATION AND CHARACTERIZATION OF MgB_2/Fe BY EX-SITU PIT METHOD

High-Temperature Synthesis of Superconducting MgB2 Materials in a Centrifuge

Superconducting properties of nanocrystalline MgB$_2$