Abstract:Convective drying of wastewater sludges and sawdust/sludge mixtures was studied. The first part of this work was an experimental study performed in a cross-flow convective dryer using 500 g of wet material extruded through a disk with circular dies of 12 mm. The results showed that the sawdust addition has a positive impact on the drying process from a mass ratio of 2/8, on a dry basis, with observed drying rates higher than the original sludge. The second part of this work consisted of developing a drying model in order to identify the internal diffusion coefficient and convective mass transfer coefficient from the experimental data. A comparison was made between fitted drying curves, well represented by the Newton's model, and the analytical solutions of the diffusion equation applied to a finite cylinder. Variations of dimensional characteristics, such as the volume and exchange surface of the sample bed, were obtained by X-ray tomography. This technique allowed us to confirm that shrinkage, which is an important phenomenon occurring during sludge and sawdust/sludge mixture drying, must be taken into account. The results showed that both the internal diffusion coefficient and convective mass transfer coefficient were affected by mixing and sawdust addition. The internal diffusion coefficient changed from 7.77 × 10−9 m2/s for the original sludge to 7.01 × 10−9 m2/s for the mixed sludge and then increased to 8.35 × 10−9 m2/s for the mixture of a mass ratio of 4/6. The convective mass transfer coefficient changed from 9.70 × 10−8 m/s for the original sludge to 8.67 × 10−8 m/s for the mixed sludge and then increased to 12.09 × 10−8 m/s for the mixture of a mass ratio of 4/6. These results confirmed that sawdust addition was beneficial to the sludge drying process as the mass transfer efficiency between the air and material increased. Reinforcing the texture of sludge by adding sawdust can increase the drying rate and decrease the drying time, and then the heat energy supply will be reduced significantly. The study also showed that neglecting shrinkage phenomenon resulted in an overestimation for the internal diffusion coefficient for the convective drying of sludges and sawdust/sludge mixtures.

Analysis of the effect of intrinsic sludge properties on sludge drying characteristics from both sludge composition and type scales

Measurement and Modelling of Moisture Distribution and Water Binding Energy of Dredged Sludge

Effects of Air Parameters on Sewage Sludge Drying Characteristics and Regression Analyses of Drying Model Coefficients

Analysis of the Shrinkage Effect on Mass Transfer During Convective Drying of Sawdust/Sludge Mixtures

Enhancement of conductive drying of sewage sludge with mechanical compression: Drying kinetics, and interfacial heat transfer behavior

Research on Sludge Drying Characteristics in a Double-Axis Paddle Dryer by Coupling Markov Chain and Penetration Theory

Methods, mechanisms, models and tail gas emissions of convective drying in sludge: A review

Effects of Air Temperature and Humidity on the Kinetics of Sludge Drying at Low Temperatures

Relation between hydrophilic/hydrophobic characteristics of sludge extracellular polymeric substances and sludge moisture-holding capacity in hot-pressing drying

Mechanical compression assisted conductive drying of thin-film dewatered sewage sludge: Process performance, heat and mass transfer behavior

Mathematical Modeling of Thin-layer Infrared Drying of Dewatered Municipal Sewage Sludge (DWMSS)

Comparative Study on Drying Characteristics of Sewage Sludge in Two Kinds of Indirect Heat Drying Equipment

Characteristics and Model of Sludge Adhesion During Thermal Drying.

Experimental and modeling study of the long cylindrical oily sludge drying process

Multiscale experimental insights into vacuum drying of sludge for enhanced energy efficiency and emission control

Emission Characteristics and Formation Mechanism Analysis of Exhaust during Sludge Thermal Drying Process

Influence of drying methods on the thermodynamic parameters, effective moisture diffusion and drying rate of wastewater sewage sludge

Sensitivity analysis of structural parameters of a low-temperature heat pump sludge drying system

Enhancing data reliability in quantitative characterization of moisture distribution in sludge using DSC: Impact of sample attributes and test parameters

Reinforced contact between sludge and hot wall for enhancing conductive drying by applying external load: Heat and mass transfer analysis

Drying characteristics of sewage sludge pre-conditioned by CaO and sawdust under low-temperature drying conditions