Abstract:A novel Ni-Co-Cr-based medium-entropy superalloy with a high Si content (7.5 at%) strengthened by an L12 phase was developed. The pure L12 phase, characterized by an average size of 50 nm and a volume fraction of 46%, was precipitated within the FCC matrix. This alloy exhibits excellent mechanical properties over a wide range of temperatures from 77 K to 1073 K. A yield strength of 1005 MPa, an ultimate tensile strength of 1620 MPa, and a tensile elongation of 36% were achieved at 77 K, with a maximum value of 4.8 GPa at the second stage of the work-hardening rate. The alloy maintains a basically consistent yield strength of approximately 800 MPa from 298 K to 973 K, showcasing significant strain-hardening capabilities, with values of 2.5 GPa, 3.7 GPa, and 4.8 GPa at 873 K, 298 K, and 77 K, respectively. Microscopic analysis revealed that at room and cryogenic temperatures, multilayer stacking faults (SFs), SF bands, and SF networks, rather than twins, effectively stored a large number of dislocations and impeded dislocation movement, thereby enhancing the work-hardening ability of the alloy. Furthermore, at 773 K, the primary deformation mechanism involved high-density dislocation walls (HDDWs) consisting of dislocation tangles and SF lines. As the temperature rose to 973 K, the work-hardening process was influenced by the APB shearing mechanism (in the form of dislocation pairs), SF lines, and microtwins generated through atomic rearrangement. This study not only provides valuable insights for the development of new oxidation-resistant superalloys but also enhances our understanding of high-temperature deformation mechanisms.

Toward Enhanced Strength and Ductility of Al–14.5Si Alloy via Solidification Under Super‐Gravity Field

Influence of Super-Gravity Coefficient on Spatial Distribution of Solidification Structure in Al-14.5Si Alloys

Refining Mechanism and Elevated-Temperature Mechanical Properties of Al-Ce Alloys Solidified under Super Gravity Field

Super-gravity field assisted homogeneous distribution of sub-micron eutectic Si in Al-Si alloy

Growth Mechanism of Eutectic Si in Super-Gravity Solidified Al-Si Alloy During Annealing

Towards enhanced elevated-temperature mechanical properties by regulation of eutectic structure in Al-Cu-Si alloys solidified under super-gravity field

Achieving Enhanced Strength Retention at Elevated Temperatures in Ultrafine-Fibrous Interconnected Al-Ce-Ni Eutectic Alloy Solidified under Super-Gravity Field

Interfacial Regulation and Fracture Mechanism of Al–Si/SiC Composites Infiltrated under Super-Gravity Field

Effects of Super-gravity Field on Solidification Structure and Microhardness of Al-Ni-Cr Alloy

Influence of Super Gravity Field on Solidification Structures of Cu98.4 Cr1.6 Alloy

Effects of High Gravity Field on Microstructure and Properties of ZL205A Alloy

Influence of Reinforcement with Multimodal Distribution on Thermophysical Properties and Fracture Behavior in Al-Si/SiC Composites Infiltrated under Super-Gravity Field

Influence of Annealing Time on Microstructure and Mechanical Properties of Al-14.5Si Alloy Prepared by Super-Gravity Solidification and Cold-Rolling

Bulk nanostructured Al-Si alloy with remarkable improvement in strength and ductility

Influence of Co Contents and Super-Gravity Field on Refinement of In-Situ Ultra-Fined Fibers in Al-2.5Ni Eutectic Alloys

Effect of Supergravity Field on the Microstructure and Mechanical Properties of Highly Conductive Cu Alloys

Evolution of solidification structure and mechanical preperties of Al7050 alloy under hypergravity

Graded microstructures of Al-Li-Mg-Zn-Cu entropic alloys under supergravity

Achievement of High Strength and Ductility in Al–Si–Cu–Mg Alloys by Intermediate Phase Optimization in As-Cast and Heat Treatment Conditions

Temperature-Dependent Mechanical Behaviors and Deformation Mechanisms in a Si-Added Medium-Entropy Superalloy with L12 Precipitation

Enhanced strength-ductility synergy in a rheo-diecasting semi-solid aluminum alloy