Abstract:Additive manufacturing (AM) introduces unique grain feature and anisotropy in metals, as well as relatively poor surface quality, so the knowledge about the formation of post-machining-induced surface integrity needs to be extended. This study aims to understand the machining phenomena in orthogonal cutting of Inconel 718 produced via powder bed fusion of metals using a laser beam system (PBF-LB/M), paying particular attention to the cutting energy, chip formation, geometrical defects, and microstructural deformation. Experiments are conducted on both wrought (W 718) and PBF-LB/M (PBF 718) Inconel 718, whereby the cutting speed and the anisotropy of the workpiece in the raw state play an important role. The results indicate that less cutting energy is consumed when cutting PBF 718 in the direction perpendicular to its build direction (BD), followed by cutting in its BD. Denser shearing-induced slip lines and relatively continuous chip morphology are found when cutting PBF 718 in its BD, moreover, the effect of cutting speed on shearing deformation of columnar grains under this condition is analysed. More importantly, this study identifies a significant geometrical defect phenomenon which is unique to PBF 718 and highly depends on the cutting speed and anisotropy of grain feature. A detailed characterisation shows that this behaviour is caused by tearing within the grains in the matrix material and not by the presence of hard inclusions, which has rarely been reported in the literature. The microstructure in the subsurface area exhibits that the density of grain boundaries in the cutting direction plays the key role in plastic deformation, as the machining process mainly causes dragging behaviour in the area below the machined surface. Thus, cutting PBF 718 in the direction perpendicular to its BD shows similar deformation layer to W 718, while cutting PBF 718 in its BD displays much stronger subsurface deformation. The obtained results greatly help to understand the cutting phenomena in post-machining of additively manufactured Ni-based components, especially the integrity for a better functional surface.

Dynamic behavior and formation mechanism of shear band during high-speed cutting Inconel 718

Finite Element Analysis of Adiabatic Shear Band Formation in Titanium Alloy Cutting Process

Finite Element Simulation of High-Speed Cutting

A GND simulation model for micro-deformation mechanism analyses in high-speed cutting Inconel718

Understanding The Deformation Of Metals In High Speed Cutting

In situ thermomechanical analysis of the primary shear zone in Inconel 718 orthogonal cutting

Microstructure-Based Flow Stress Model to Predict Machinability of Inconel 718

Two-dimensional evolution of temperature and deformation fields during dynamic shear banding: In-situ experiments and modeling

Chip Formation Mechanism of Inconel 718: A Review of Models and Approaches

Effect of Grain Size on Deformation and Fracture of Inconel718: an In-Situ SEM-EBSD-DIC Investigation

On machining-induced surface integrity of Inconel 718 fabricated by powder bed fusion

Microstructural Evolution of Shear Localization in High-Speed Cutting of CoCrFeMnNi High-Entropy Alloy

The effect of chip formation on the cutting force and tool wear in high-speed milling Inconel 718

Machining-Induced Work Hardening Behavior of Inconel 718 Considering Edge Geometries

Experimental and numerical investigation of Inconel 718 machining with worn tools

Dynamic shear behavior of forged CrMnFeCoNi high entropy alloy using hat-shaped specimens over a wide range of temperatures and strain rates

Effect of workpiece microstructure on tool wear behavior and surface quality during machining Inconel 718 alloy

Wear mechanism, subsurface structure and nanomechanical properties of additive manufactured Inconel nickel (IN718) alloy

Development of an analytical model to investigate the effect of tool geometry and cutting parameters on the milling performance of Inconel 718

Transient Temperature at Tool–Chip Interface during Initial Period of Chip Formation in Orthogonal Cutting of Inconel 718

The microstructural evolution and mechanical response of laser direct energy deposition Inconel 718 alloy based on simulation and experimental methods