Abstract:Controlling the hot deformation mechanism of the titanium alloy and avoiding deformation instability are the key points in the hot forging of the titanium alloy. A high throughput experimental method was used to establish a deformation mechanism map efficiently. A continuously varying strain distribution from 0.3 to 1.4 was obtained by the deformation of the double-cone specimens. At the temperature of 910 °C and the strain rate of 1.37 s −1 , Combining the analysis of metallography and strain-stress curves, the deformation mechanisms in different regions of the double-cone specimens were divided. Dynamic recovery (DRV) and dynamic recrystallization (DRX) work together in the low strain region (<0.62), and DRX gradually becomes the dominant deformation mechanism in the medium strain region (0.62–1.02). In the large strain region (1.02–1.4), amounts of deformation bands (DBs) formed. Electron back scatter diffraction (EBSD) technique was used for the microstructure observation and the analysis of deformation mechanism. The results demonstrate that with an increase in strain, the recrystallization fraction increased from 83.8% to 96.3%. Combining the several results of the double-cone specimens, the hot deformation mechanism diagram with a temperature range of 850–930 °C, and a strain range of 0.3–1.4 was established. When the strain reaches a certain degree, it is difficult to further form new recrystallized grains at the grain boundaries. The formation of recrystallized grains within the deformation band has been characterized using transmission electron microscopy (TEM). Under the action of shear force, fine recrystallized grains form within the elongated grains. The concentrated fine recrystallized grains aggravate the microstructural nonuniformity of the Ti-55511 titanium alloy in this area, which finally leads to the deformation instability.

Interface Stress Evolution of High-Strength Titanium-Steel Composite Pipe during Hot Extrusion

Interface bonding and mechanical properties of large explosively welded titanium/aluminum composite pipes

Flow characteristics, ANN-based prediction, 3D processing map, and interface microstructure of titanium/stainless steel bimetallic composite

Interface Behaviors and Mechanical Properties of Diffusion Bonded 45 Steel/additive Manufactured 316L Steel Joints

Interface evolution mechanism and mechanical properties of Ti311/TC4 laminated composites during hot-pressing diffusion bonding

Hot deformation behavior and microstructure evolution of TC11 dual-phase titanium alloy

Microstructure Evolution and Deformation Behavior of High Strength Titanium Clad Steel Plate in the Thermal Compression

Evolution mechanism of microstructure and bond strength based on interface diffusion and IMCs of Ti/steel clad plates fabricated by double-layered hot rolling

Interfacial reaction behavior of titanium/steel composite plate formed by cold-hot rolling

A novel high entropy composite interlayer for diffusion bonding of TC4 titanium alloy to 316 L stainless steel

Finite Element Simulation of Extrusion Process of TC4 Titanium Alloy Profile

Metal Behavior of Hot Extrusion Deformation and Microstructural Analysis of TA15 Titanium Alloy

Deformation mechanism diagram and deformation instability of a Ti-5Al-5Mo-5V-1Cr-1Fe titanium alloy during the hot compression

The Interface Structure and Its Impact on the Mechanical Behavior of TiAl/Ti2AlNb Laminated Composites

Effects of Interface Roughness on the Annealing Behaviour of Laminated Ti-Al Composite Deformed by Hot Rolling

Finite element simulation and experimental research on multi-pass hot deformation behavior of Ti-Zr composite microalloyed steel

The Interrupted Hot Compression of an As-Forged Titanium Matrix Composite: Flow Softening Behavior and Deformation Mechanism

Effects of temperature on interfacial evolution and mechanical properties of pure titanium and carbon steel sheets bonded via new multi-pass continuous hot-roll diffusion with nickel interlayer

Study on interfacial microstructure and shear strength of hot-compression bonded Ti386/TC4

Hot compressive deformation of eutectic Al-17at% Cu alloy on the interface of the Cu-Al composite plate produced by horizontal continuous casting

Study of Internal Pressure Strength of the Titanium-Steel Composite Tube Based on Yield and Shear Failure Mechanisms