Abstract:Summary In preferentially oil-wet porous media, laboratory waterflooding experiments are prone to capillary end effects. The wetting phase (oil) will tend to accumulate at the outlet where the capillary pressure is zero and leave a highly remaining-oil saturation at steady state (defined by a stable pressure drop and a zero oil-production rate) compared to the residual-oil saturation. Andersen et al. (2017c) derived analytical solutions describing how the capillary pressure and relative permeability of water (the injected phase) could be determined on the basis of pressure drop and average saturation at steady states obtained at different water-injection rates. Plotting these values against inverse rate reveals linear trends at high rates, with slopes and intercepts that directly quantify the saturation functions in the range of negative capillary pressures. The method is similar to the Gupta and Maloney (2016) intercept theory but quantifies entire functions rather than a single point and provides the trends also at low rates, thus using all the information. Our aim is to demonstrate how pressure drop and oil production at steady state for different water-injection rates can be used to derive relative permeability and capillary pressure from waterflooding. This is done in three ways. First, synthetic transient waterflooding tests are generated (using a core-scale simulator), applying the same saturation-function correlations as assumed in the analytical solution. Then, more-general correlations are assumed when generating the synthetic data. This is to test the robustness of the analytical solution in producing functions similar to the “true” ones. Finally, we perform a waterflooding experiment in the laboratory on a high-permeability (3 darcies) Bentheimer sandstone core, altered to an oil-wet state. Forced imbibition was started at a rate of 0.4 pore volumes (PV) per day, which was increased stepwise after approaching a steady state. Twelve rates were applied, differing overall by a factor of ≈1,000 to yield states governed by capillary forces and advective forces. The results were interpreted using both full history matching of the transient data and matching of the steady-state data with the analytical solution. The experimental procedure and model demonstrate that only water relative permeability and capillary pressure determine the steady state during waterflooding, and hence can be estimated accurately. The analytical solution could simultaneously match the trends and magnitude of a steady-state pressure drop and production with injection rate to give an estimation of the saturation functions. The estimated saturation functions from the analytical solution agreed well with the estimates from full history matching.

Relative permeability hysteresis and residual trapping in rough-walled fractures: An experimental investigation of the effects of flow rate and saturation history using the steady-state approach

Steady-state Two-phase Relative Permeability Measurements in Proppant-packed Rough-walled Fractures

Analytical Models and Experimental Verifications for Relative Permeabilities of Oil-Water Two-Phase Flow in Fractures

Imaging and Measurement of Pore‐Scale Interfacial Curvature to Determine Capillary Pressure Simultaneously with Relative Permeability

Study of Oil-Water Two-Phase Stratified Flow in Horizontal Fractures

Tensor Analysis of the Relative Permeability in Naturally Fractured Reservoirs

Modeling Two-Phase Flow in Tight Core Plugs with an Application for Relative Permeability Measurement

Simultaneous Interpretation of Relative Permeability and Capillary Pressure for a Naturally Fractured Carbonate Formation From Wireline Formation Testing

Permeabilities of Water–Oil Two-Phase Flow in Capillary Fractures with Different Wettabilities

Numerical Simulations of Geomechanical Deformation, Fluid Flow and Reactive Transport in Shale Rough-Walled Microfractures

Relative Permeability of Two-Phase Fluid Flow Through Rough Fractures: the Roles of Fracture Roughness and Confining Pressure

A FRACTAL-MONTE CARLO APPROACH TO MODEL OIL AND WATER TWO-PHASE SEEPAGE IN LOW-PERMEABILITY RESERVOIRS WITH ROUGH SURFACES

Experimental Verification of Reservoirs with Different Wettability Using an Oil–Water Relative Permeability Model

A COMPREHENSIVE MODEL FOR OIL–WATER RELATIVE PERMEABILITIES IN LOW-PERMEABILITY RESERVOIRS BY FRACTAL THEORY

Simulation Interpretation of Capillary Pressure and Relative Permeability From Laboratory Waterflooding Experiments in Preferentially Oil-Wet Porous Media

Investigation on the microscopic damage mechanism of fracturing fluids to low-permeability sandstone oil reservoir by nuclear magnetic resonance

The Mechanism Study of Fracture Porosity in High-Water-Cut Reservoirs

Relative Permeability Calculations from Two-Phase Flow Simulations Directly on Digital Images of Porous Rocks

An Analytical Relative Permeability Model Considering Flow Path Structural Characteristics for Gas-Liquid Two-Phase Flow in Shale Fracture

Nonlinear Flow and Permeability Anisotropy Characteristics in Hydraulic Fracturing-Induced Rock Fractures Subjected to Various Normal Compressive Stresses

Impact of effective stress on permeability for carbonate fractured-vuggy rocks