Abstract:The scope of this work is to provide an overview of the influences of process parameters, print orientation, and post-process treatments of Ti6AlV4 processed by laser powder bed fusion on its microstructure and physical and mechanical properties and their anisotropic behavior. To avoid the influence of changes in powder quality and ensure comparability, experiments were carried out using a single batch of virgin powder. First, characterization of the density and surface roughness was performed to optimize the process parameters utilizing design of experiment. Tensile, notched bar impact and compression test specimens were built in three different orientations: vertically, horizontally, and inclined at 45° to the build plate. Later, the influence of the staircase effect and the possible course of anisotropy from vertical to horizontal were investigated. Subsequently, heat treatments for stress relief, furnace annealing, and hot isostatic pressing were performed. In addition to as-built samples, mechanical machining and a two-step electrochemical polishing surface treatment were applied to investigate the influence of the surface roughness. With parameter optimization, a relative density of 99.8% was achieved, and surface roughness was improved over default parameters, reducing Ra by up to 7 μm. Electrochemical polishing is a viable way to decrease the surface roughness. An Ra value of 1 μm and an Rz value of 4 μm can be achieved for 45° downskin surfaces with as-built surface roughness values of Ra 24 μm and Rz 117 μm. As-built and stress-relieved conditions show little anisotropy in their yield and tensile strength (max 2.7%), but there is a strong influence of the build orientation on necking, and brittle fracture behavior is shown due to the martensitic microstructure (up to 70%). Heat treatment can increase the ductility and further decrease the strength anisotropy with both furnace annealing and hot isostatic pressing delivering similar results for tensile properties, while angled samples exhibit behavior that is closer to vertical than horizontal, indicating a non-linear change in break behavior. Electrochemical polishing increases fracture necking, and its isotropy drastically increases from 4% to over 30% compared with as-built parts, which is close to the level of the machined specimen.

Solid Particle Erosion Behaviour of Laser Sintered Heat Treated Ti–6A1–4V Alloy

Effect of Laser Sintering Parameters on the Microstructure, Mechanical Properties and Corrosion Behavior of Titanium Grade 5 Alloy

Solid particle erosion behavior and failure mechanism of TiZrN coatings for Ti-6Al-4V alloy

Wear and Failure Analysis of Ti-6Al-4V Titanium Alloy with a Protective Coating during High-Speed Erosion

Laser surface modification of Ti--6Al--4V: wear and corrosion characterization in simulated biofluid

Al2O3 Particle Erosion Induced Phase Transformation: Structure, Mechanical Property, and Impact Toughness of an SLM Al-10Si-Mg Alloy

Effect of Heat Treatments on Mechanical Properties and Wear Resistance of Laser-Powder Bed-Fused Ti6Al4V Alloy

Effect of Build Orientation and Heat Treatment on Erosion Behavior of Al10SiMg Fabricated Using Laser Powder Bed Fusion

Laser Additive Manufactured Ti–6Al–4V Alloy: Heat Treatment Studies

MORPHOLOGY OF WEAR DEBRIS DURING DRY SLIDING OF Ti6Al4V/TiC COMPOSITE AT ELEVATED TEMPERATURES IN VACUUM CONDITIONS

Erosion Behavior of Ti-hBN Multifunctional Coatings in a Custom-made Planetary Test Rig at Extreme Lunar Temperatures

Characterization of Ti6Al4V Alloy Produced by Laser-Powder Bed Fusion and Surface Modification Using Nanosecond Laser

High-Temperature Tribology of Selective Laser-Melted Titanium Alloys: Role of Adhesive Wear

The effect of laser surface re-melting on the surface roughness and micro-hardness of selective laser melting (SLM) fabricated Ti-6Al-4V samples

Analysis of laser power/scan speed combinations on constant energy density: Correlation of roughness-density and structure-property of additively manufactured Ti-6Al-4 V alloy

On Strain-Hardening Behavior and Ductility of Laser Powder Bed-Fused Ti6Al4V Alloy Heat-Treated above and below the β-Transus

Study on machinability characteristics of novel additive manufactured titanium alloy (Ti-6Al-4V) fabricated by direct metal laser sintering

Influences of Surface, Heat Treatment, and Print Orientation on the Anisotropy of the Mechanical Properties and the Impact Strength of Ti 6Al 4V Processed by Laser Powder Bed Fusion

Microstructure and High-Temperature Tribological Properties of Ti–6Al–4V Alloy Treated by Laser Shock Peening

Effects of Heat Treatments on Microstructures and Mechanical Properties of Ti6Al4V Alloy Produced by Laser Solid Forming

Microstructural Strengthening and Plastic Degradation of Ti–6Al–4V Induced by Laser Ablation