Abstract:In WWTP models, the accurate assessment of solids inventory in bioreactors equipped with solid-liquid separators, mostly described using one-dimensional (1-D) secondary settling tank (SST) models, is the most fundamental requirement of any calibration procedure. Scientific knowledge on characterising particulate organics in wastewater and on bacteria growth is well-established, whereas 1-D SST models and their impact on biomass concentration predictions are still poorly understood. A rigorous assessment of two 1-DSST models is thus presented: one based on hyperbolic (the widely used Takács-model) and one based on parabolic (the more recently presented Plósz-model) partial differential equations. The former model, using numerical approximation to yield realistic behaviour, is currently the most widely used by wastewater treatment process modellers. The latter is a convection-dispersion model that is solved in a numerically sound way. First, the explicit dispersion in the convection-dispersion model and the numerical dispersion for both SST models are calculated. Second, simulation results of effluent suspended solids concentration (XTSS,Eff), sludge recirculation stream (XTSS,RAS) and sludge blanket height (SBH) are used to demonstrate the distinct behaviour of the models. A thorough scenario analysis is carried out using SST feed flow rate, solids concentration, and overflow rate as degrees of freedom, spanning a broad loading spectrum. A comparison between the measurements and the simulation results demonstrates a considerably improved 1-D model realism using the convection-dispersion model in terms of SBH, XTSS,RAS and XTSS,Eff. Third, to assess the propagation of uncertainty derived from settler model structure to the biokinetic model, the impact of the SST model as sub-model in a plant-wide model on the general model performance is evaluated. A long-term simulation of a bulking event is conducted that spans temperature evolution throughout a summer/winter sequence. The model prediction in terms of nitrogen removal, solids inventory in the bioreactors and solids retention time as a function of the solids settling behaviour is investigated. It is found that the settler behaviour, simulated by the hyperbolic model, can introduce significant errors into the approximation of the solids retention time and thus solids inventory of the system. We demonstrate that these impacts can potentially cause deterioration of the predictive power of the biokinetic model, evidenced by an evaluation of the system's nitrogen removal efficiency. The convection-dispersion model exhibits superior behaviour, and the use of this type of model thus is highly recommended, especially bearing in mind future challenges, e.g., the explicit representation of uncertainty in WWTP models.

Success and shortcomings of clarifier modelling

Mathematical Modelling of Expanded Bed Adsorption – a Perspective on in Silico Process Design

Modification in Barcelona Model and Further Researches

Improved Model of Secondary Clarifier in A2/O Process

A Force-Based Mechanistic Model for Describing Activated Sludge Settling Process

Shall we upgrade one-dimensional secondary settler models used in WWTP simulators? - An assessment of model structure uncertainty and its propagation

Mini-review of sewage sludge parameters related to system modelling

The Whole Process CFD Numerical Simulation of Flow Field and Suspended Solids Distribution in a Full-Scale High-Rate Clarifier

Flocculation modelling: a review

Modelling of Membrane Fouling in a Submerged Membrane Bioreactor

Deep deconstruction and future development of process-based models for subsurface flow constructed wetlands

Multiphase Flow Models in Quantifying Constant Pressure Dead-End Filtration and Subsequent Cake Compression - 1. Dilute Slurry Filtration

A review of sewage sludge dewatering and stabilisation in reed bed system: towards the process-based modelling

Plant-wide modelling of phosphorus transformations in wastewater treatment systems: Impacts of control and operational strategies

Numerical Modeling of Flow in Chlorine Disinfection Tanks

Foundation and challenges in modelling Dilute Active Suspensions

An improved 1D reactive Bürger-Diehl settler model for secondary settling tank denitrification

Modelling Study of Dishwasher Hydraulic Filtration System

A Simplistic Mathematical Model for Carbon Oxidation in Moving Bed Bioreactor

The Limitations in Current Studies of Organic Fouling and Future Prospects

Development and applications in computational fluid dynamics modeling for secondary settling tanks over the last three decades: A review