Abstract:This study presented the UV‐initiated methods to graft polyacrylamide (PAM) hydrogel on the surface of polyester (PET) fibers toward the one‐step and the two‐step methods. The results of the study indicate that PAM hydrogels can enhance the hydrophilic property of PET fibers. Additionally, the modified PET fibers exhibit the swelling properties. It is widely recognized that polyester (PET) fibers with swelling properties are necessary for advanced applications of PET fibers in waterproof fabrics. This study presented the UV‐initiated methods to graft polyacrylamide (PAM) hydrogel on the surface of PET fibers. In the one‐step method, PET fibers are impregnated with a mixed solution of the photoinitiator benzophenone (BP) and the monomer acrylalkylamine (AM). Then, the PET fiber was directly exposed to UV light. In the two‐step method, PET fibers were first impregnated with a photoinitiator solution to generate BP radicals. Then, the fibers impregnated with a monomer solution before being grafted by UV light. Both two methods ultimately achieve PAM gelation‐modified PET fibers. The chemical composition and surface structure were detected by Fourier transform infrared spectroscopy and scanning electron microscope. The findings demonstrate that the PAM hydrogel was successfully grafted on the PET fibers through one‐step method or a two‐step method. In addition, the properties of the grafted PET fibers were evaluated by grafting yield, contact angle, and swelling test. The study indicated that the modified PET fibers via a two‐step method exhibited a superior grafting yield up to 29.3% (PET‐2n) and 54% (PET‐2) compared to the one‐step technique (PET‐1). It was shown that the grafting efficacy of PET fibers modified by two‐step method is better than one‐step method. The static contact angles of PET fibers by UV‐Induced were all reduced. For instance, the contact angles of PET‐2n were decreased from 115° to 62.9°; and the two‐step modified PET fiber after acetone cleaning (PET‐2) decreased from 115° to 60°. It was suggested that the hydrophilicity of the modified PET fibers significantly increased. In addition, the research shows that the gelation‐modified fibers were all possessed swelling properties.

Microstructure and Performance Study of PETMF/WPU Composites Prepared by Water‐Soluble Method

Effect of Sepiolite-Loaded Fe<sub>2</sub>O<sub>3</sub> on Flame Retardancy of Waterborne Polyurethane

Development of Water Soluble PBT and Superfine Fibers Thereof

Study of ‘One-Step’ Preparation of R-Pet Fiber-Reinforced PE Composites

Rapid preparation of PET-PVDF Janus fiber felt for emulsion separation

Hydrophilic Modification of Polyester/Polyamide 6 Hollow Segmented Pie Microfiber Nonwovens by UV/TiO2/H2O2

Study of Water Soluble Island-in-sea PET Fiber

Surface Modification of PET Fiber with Hybrid Coating and Its Effect on the Properties of PP Composites.

Synthesis and properties of waterborne polyurethane-based PTMG and PDMS as soft segment

Regulation of Dielectric and Microwave Absorption Properties of Needle-Punched Polyimide/carbon Fiber Nonwoven Composites in X-band

Investigation on the Effect of Fiber Wettability on Water Absorption Kinetics of Geopolymer Composites

Preparation and characterization of high‐solid carboxylate/sulfonate waterborne polyurethane and its application in novel water‐based superfine fiber synthetic material

Highly Filled Waste Polyester Fiber/Low-Density Polyethylene Composites with a Better Fiber Length Retention Fabricated by a Two-Rotor Continuous Mixer

A novel method for the synthesis of solvent‐free and high‐solid‐content waterborne polyurethanes by introducing a small amount of polyethylene glycol

Reuse polyester/cotton blend fabrics to prepare fiber reinforced composite: Fabrication, characterization, and interfacial properties evaluation

A Review of Waterborne Polyurethane Coatings and Adhesives with Polyester Polyol from Poly(Ethylene Terephthalate) Waste

A novel wood fiber/waterborne epoxy resin composite with high fiber content and performance fabricated by a green and simple process

High-value utilization method of digital printing waste paper fibers-Co-blending filled HDPE composites and performance improvement

Different Effects of Mixing Manners on the Porous Structures and Dense Films of Waterborne Polyurethane Modified with Recycled Aramid Nanofibers

Preparation and properties of polyester fibers with polyacrylamide hydrogel grafted by UV‐irradiation

Characterization and Application to Fiber Reinforced Composite of Catechol/polyethyleneimine Modified Polyester Fabrics by Mussel-inspiration