Fabrication of cadmium indium sulfide/cadmium sulfide/polyoxo-titanium cluster composite nanofibers with enhanced photocatalytic activity for nitrite degradation

Yuan-ping Zhou,Jing Wang,Qing-yun Liu,Min Peng,Yong-zhen Zhao,Qun-liang Li,Youyan Liu,Hai-Bo Liu

DOI: https://doi.org/10.1016/j.seppur.2021.118831

IF: 8.6

2021-09-01

Separation and Purification Technology

Abstract:Photocatalytic removal of nitrite is a convenient and green method. Photocatalytic technology has been limited, however, by its light absorption range and unsuitable conduction and valence bands, which affect the photocatalytic efficiency and nitrogen selectivity. In this work, we synthesized a cadmium indium sulfide/cadmium sulfide/polyoxo-titanium cluster composite nanometer photocatalyst with a visible light response, and further fixed the photocatalyst to fibers to form electrospun film. The samples were characterized using direct reflectance spectroscopy, scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, photoluminescence, Fourier-transform infrared spectroscopy, N2 adsorption–desorption isotherms, and the transient photocurrent response. The photocatalytic activity of the prepared photocatalyst was evaluated based on the transformation of nitrite under simulated sunlight. The photocatalytic results showed that the nitrite conversion rate was as high as 98% within 2 h and had about a 63% selectivity of nitrogen. The combination of CdS and Cdln2S4 better captured visible light and could be adjusted to an appropriate oxidation–reduction potential energy after loading with polyoxo-titanium clusters. Subsequently, the results of cycling experiments indicated that the Cdln2S4/CdS/polyoxo-titanium clusters composite nanofibers maintained a fairly consistent photocatalytic performance. The effects of electron and hole scavengers were investigated and the possible photocatalytic mechanism was elucidated by studying the products during the photocatalytic degradation.

engineering, chemical

What problem does this paper attempt to address?

The main problem this paper attempts to address is the development of an efficient photocatalyst for the degradation of nitrite in water under visible light. Specifically, the researchers synthesized a composite nanofiber photocatalyst composed of cadmium indium sulfide (CdIn₂S₄), cadmium sulfide (CdS), and polyoxo-titanium cluster (PTC-3), and immobilized it on electrospun fibers to enhance its photocatalytic activity and reusability.

### Main Issues:
1. **Efficient Photocatalytic Degradation of Nitrite**:
- Nitrite is a toxic substance, and high concentrations of nitrite pose a serious threat to water environments and human health.
- Existing treatment methods such as reverse osmosis, electrodialysis, ion exchange, and biodegradation have high costs, complex operations, and long cycles, making them difficult to apply widely.
- Photocatalytic technology has become an effective method for treating nitrite due to its low cost, simple operation, and thorough degradation of pollutants.

2. **Improving Photocatalyst Performance**:
- Traditional photocatalysts such as titanium dioxide (TiO₂) produce a large number of by-products during the photocatalytic degradation of nitrite, affecting their efficiency and selectivity.
- Metal sulfides (such as CdIn₂S₄ and CdS) have good light absorption properties but suffer from photo-corrosion, limited active sites, and high electron-hole recombination rates.
- By introducing polyoxo-titanium cluster (PTC-3), the band structure of the composite material can be adjusted to improve its photocatalytic performance.

3. **Preparation of Stable Composite Nanofibers**:
- Immobilizing the photocatalyst on nanofibers through electrospinning technology can not only enhance the stability and reusability of the photocatalyst but also increase its specific surface area, thereby improving photocatalytic activity.
- The researchers experimentally verified the photocatalytic performance of these composite nanofibers under visible light and conducted cyclic experiments to confirm their stability.

### Solutions:
- **Material Synthesis**: The CdIn₂S₄/CdS/PTC-3 composite photocatalyst was prepared by hydrothermal and in-situ synthesis methods and immobilized on nanofibers through electrospinning technology.
- **Performance Testing**: Various characterization techniques (such as X-ray diffraction, scanning electron microscopy, transmission electron microscopy, Fourier-transform infrared spectroscopy, etc.) were used to analyze the structure and performance of the composite material in detail.
- **Photocatalytic Experiments**: Under simulated sunlight, the photocatalytic degradation performance of the composite nanofibers for nitrite was evaluated, showing a nitrite conversion rate of up to 98% within 2 hours and a nitrogen selectivity of about 63%.
- **Cyclic Experiments**: Multiple cyclic experiments were conducted to verify the stability and reusability of the composite nanofibers.

In summary, this paper aims to develop an efficient and stable photocatalyst for the degradation of nitrite in water under visible light to address the limitations of existing treatment methods.