Abstract:Flexible pressure sensors have attracted intense attention because of their widespread applications in electronic skin, human–machine interfaces, and healthcare monitoring. Conductive porous structures are always utilized as active layers to improve the sensor sensitivities. However, flexible pressure sensors derived from traditional foaming techniques have limited structure designability. Besides, random pore distribution causes difference in structure and signal repeatability between different samples even in one batch, therefore limiting the batch production capabilities. Herein, we introduce a structure designable lattice structure pressure sensor (LPS) produced by bottom-up digital light processing (DLP) 3D printing technique, which is capable of efficiently producing 55 high fidelity lattice structure models in 30 min. The LPS shows high sensitivity (1.02 kPa<sup>–1</sup>) with superior linearity over a wide pressure range (0.7 Pa to 160 kPa). By adjusting the design parameters such as lattice type and layer thickness, the electrical sensitivities and mechanical properties of LPS can be accurately controlled. In addition, the LPS endures up to 60000 compression cycles (at 10 kPa) without any obvious electrical signal degradation. This benefits from the firm carbon nanotubes (CNTs) coating derived from high-energy ultrasonic probe and the subsequent thermal curing process of UV-heat dual-curing photocurable resin. For practical applications, the LPS is used for real time pulse monitoring, voice recognition and Morse code communication. Furthermore, the LPS is also integrated to make a flexible 4 × 4 sensor arrays for detecting spatial pressure distribution and a flexible insole for foot pressure monitoring.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c21407?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c21407</a>.Comparison of additive manufacturing techniques for preparation of porous materials for flexible electronics; optical photographs of the lattice structure green model after DLP 3D printing and after CNT coating; SEM images of bare TPU substrate and CNT-coated sample; cross-section SEM image of CNT-coated sample; tensile stress-strain curves of 3D printed pure TPU compared to PDMS and Ecoflex 00-10; optical and SEM images of conductive fabric interdigital electrode; optical photograph of LPS under a compression and release cycle at a compression rate of 0.1 mm/s; optical images of the LPSs with three lattice types ("A", "D" and "E") at various applied pressure; compressive stress–strain curves of LPSs with 5 types of lattice structure; cyclic compression test under 40 kPa at different frequencies; SEM images of LPS sample after 60 000 cycles compression test at 10 kPa with a frequency of 0.5 Hz; current response of LPS attached on the throat when saying "Printing" and "What's up"; SEM images of the surface morphology of papers with different roughness (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c21407/suppl_file/am0c21407_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Fabricating Customizable 3-D Printed Pressure Sensors by Tuning Infill Characteristics

Design Rules for 3D Printing‐Assisted Pressure Sensor Manufacturing: Achieving Broad Pressure Range Linearity

3D Printing of Highly Sensitive and Large-Measurement-Range Flexible Pressure Sensors with a Positive Piezoresistive Effect

Flexible Pressure Sensor with Micro-Structure Arrays Based on PDMS and PEDOT:PSS/PUD&CNTs Composite Film with 3D Printing

3D Printed Skin‐Inspired Flexible Pressure Sensor with Gradient Porous Structure for Tunable High Sensitivity and Wide Linearity Range

3D Printing of a Flexible Inclined‐Tip Cone Array‐Based Pressure Sensor

High-Performance Flexible Piezoresistive Pressure Sensor Printed with 3D Microstructures

InkFusion3D: 3D Printing Flexible Sensors with Silicone Rubber and Conductive Ink Materials

3D-Printed Soft Sensors for Adaptive Sensing with Online and Offline Tunable Stiffness

Study on CNT/TPU cube under the 3D printing conditions of infill patterns and density

Structural Design and DLP 3D Printing Preparation of High Strain Stable Flexible Pressure Sensors

Fabrication of high sensitivity and stable strain sensors based on composite folded structures via embedded 3D printing

Flexible Pressure Sensors Tuned by Interface Structure Design – Numerical and Experimental Study

Batch fabrication of ultrathin flexible pressure sensors enabled by full printed technique

An Ultrasensitive 3D Printed Tactile Sensor for Soft Robotics

Rational Design of 3D‐printed Metastructure‐based Pressure Sensors

Closed‐Loop Optimization of Soft Sensor Morphology Using 3D Printing of Electrically Conductive Hydrogel

Direct Printing Of Stretchable Elastomers For Highly Sensitive Capillary Pressure Sensors

Tailored and Highly Stretchable Sensor Prepared by Crosslinking an Enhanced 3D Printed UV‐Curable Sacrificial Mold

Design and Fabrication of Flexible Capacitive Sensor With Cellular Structured Dielectric Layer via 3D Printing

Facile Fabrication of Flexible Pressure Sensor with Programmable Lattice Structure