Abstract:A small gas turbine performance modeling and testing project has been completed as part of a DSTO research program. The main objective of the program was to enhance capability in understanding and modeling the thermodynamic and performance characteristics of gas turbine engines. The secondary objective of the program was development of a simple, low-cost test apparatus for basic thrust augmentation technologies and infrared suppression studies.Engine performance modeling was conducted using commercial software (Gasturb) and an in-house developed code. Various techniques were used in predicting component performance which included scaling of published performance data, use of standard empirical performance models, mean-line and through flow codes and detailed Computational Fluid Dynamics (CFD) analysis. A comparison of the advantages and disadvantages of each method was made and compared with engine test data.The AMT Olympus HP turbojet engine was used as the test engine. The engine was instrumented using a bell mouth to measure mass flow rate, load cell to measure thrust, tachometer to measure engine rotational speed, thermocouples to measure flow total temperature and pressure transducers to measure wall static pressure at various stations along the engine.A pair of Olympus engines were tested for comparison during baseline testing, with consistent results between the two. The first engine was fully instrumented and used in all of the tests. This engine was used to test the engine standard operating line tests to determine bulk performance and establish compressor operating line. Tests were repeated and error analysis conducted to ensure repeatability and validity of the data. The second engine was used as a control engine with only the OEM supplied instrumentation, thrust and bell mouth used for benchmarking purposes. The data from both engines have been compared with the engine performance model and OEM data.A number of other tests were completed to “stress” the engine and shift its operating line closer to the compressor stall line. This was accomplished through various types of exhaust blockage. Stall behaviour was clearly evident in the initial commissioning tests where a large nozzle blockage resulted in engine stall and incomplete start-up. Engine performance and compressor map results from the tests have been compared to the engine performance model with good agreement.Copyright © 2013 by Commonwealth of Australia

The Design and Optimization of Additively Manufactured Radial Compressor of a Miniature Gas Turbine Engine

Multidisciplinary optimization of the SRV2-O radial compressor using an adjoint-based approach

Optimization Of High Speed Centrifugal Compressor For A Micro Gas Turbine Based On Cfd And Fem Analysis

Multidisciplinary Design Methodology for Micro-Gas-Turbines - Part II: System Analysis and Optimization

Design Optimization of a High-Speed Twin-Stage Compressor for Next-Gen Aircraft Environmental Control System

Three-Dimensional Optimization of Blade Lean and Sweep for an Axial Compressor to Improve the Engine Performance

Experimental and Numerical Verification of an Optimization of a Fast Rotating High-Performance Radial Compressor Impeller

Design Optimisation of a Screw Compressor with a Focus on Rotor Depth: A Computational Fluid Dynamics Approach

Surrogate-Based Shape Optimization of Stall Margin and Efficiency of a Centrifugal Compressor

Multidisciplinary Design Methodology for Micro-Gas-Turbines - Part I: Reduced Order Component Design and Modelling

Design Method and Performance Prediction for Radial-Inflow Turbines of High-Temperature Mini-Organic Rankine Cycle Power Systems

Improving Vibration Response of Radial Turbine in Variable Geometry Turbochargers With CFD Analysis

Experimental Validation of an Integrated Optimization Design of a Radial Turbine for Micro Gas Turbines

Development of an Optimization Design Method for Turbomachinery by Incorporating the Cooperative Coevolution Genetic Algorithm and Adaptive Approximate Model

An Investigation Into Performance Modeling of a Small Gas Turbine Engine

Three-Dimensional Aerodynamic Optimization Of A Multi-Stage Axial Compressor

Numerical Simulation and Aerodynamic Optimization of Two-Stage Axial High-Pressure Turbine Blades

Three-Dimensional Multi-Objective Design Optimization of a 6.5-Stage Axial Flow Compressor Blades With Lean and Twist

Design, experimental investigation and multi-objective optimization of a small-scale radial compressor for heat pump applications

Geometry Scaling Technique for Aerodynamic Redesign of Multistage Transonic Compressor

Investigation on Design Flow of a Millimeter-Scale Radial Turbine for Micro Gas Turbine