Abstract:Inorganic CsPbIBr2 perovskite has been considered as a promising light-absorbing material for solar cells due to its high stability and suitable bandgap. Although the remarkable improvement of CsPbIBr2 PSC has been achieved, the efficiency of this cell is still lower than those of other analogues and far below its theoretical limit. This is mainly due to the serious charge recombination in the as-fabricated CsPbIBr2 cells derived from the poor-quality CsPbIBr2 perovskite film with a large quantity of defects and numerous grain boundaries. Therefore, fabricating high-quality CsPbIBr2 perovskite film is a key factor for the further efficiency improvement of CsPbIBr2 PSCs. Herein, phenylthiourea (PTU) additive is introduced into the CsPbIBr2 precursor to tailor the crystallization of CsPbIBr2 perovskite for fabricating high-quality CsPbIBr2 perovskite. The C=S group of PTU can coordinate with PbBr2 in the precursor owing to the lone-pair electrons on S and the empty orbits of Pb2+. The strong interaction between PTU and the CsPbIBr2 precursor components can form PTU·Pb···Br(I) intermediate phase in the precursor upon PTU introduction. The PTU·Pb···Br(I) intermediate phase can reduce the nucleation rate of perovskite and modulate the perovskite crystal growth because the extra energy is required to break the strong coordination bond in the intermediate phase, resulting in a low crystallization rate of CsPbIBr2 perovskite. Such a retardation of perovskite crystallization is conducive to the formation of high-crystallinity perovskite film with smooth surface, large crystal grains, high crystallization, and low density of defect. Meanwhile, the decomposition of PTU during thermal annealing makes the S2– inserted into interstitial of CsPbIBr2 crystal lattice, which greatly enhance the stability of CsPbIBr2 perovskite. The carbon-based PSCs with a normal n-i-p structure of FTO/compact-TiO2 layer/meso-TiO2 layer/perovskite film/carbon layer are fabricated, and their photovoltaic performances are measured under a simulated AM1.5 illumination (100 mW·cm–2). The PSC based on PTU-CsPbIBr2 perovskite delivers a high power conversion efficiency of 10.09%, which is much higher than that of the control device. This great improvement of photovoltaic performance can be attributed to the largely promoted perovskite quality, which enhances the charge collection and suppresses the charge recombination in the device. In addition, the unencapsulated device preserves 82% of the initial efficiency after being stored under ambient condition for 35 days, suggesting excellent stability. Therefore, this work provides an effective complementary strategy for effectively improving the performance of inorganic PSCs.

Mitigating defect states of all‐Inorganic CsPbI2Br perovskite via multifunctional 2‐Amino‐5‐nitrothiazole additive for an efficient air‐processed outdoor/indoor photovoltaics

Enhanced Crystallization and Optimized Morphology of Perovskite through Doping Indium-Based Metal-Organic Assembly: Achieving Significant Solar Cell Efficiency Enhancements

A Polymerization‐Assisted Grain Growth Strategy for Efficient and Stable Perovskite Solar Cells

Antisolvent‐Free Heterogenous Nucleation Enabled by Employing 4‐Tert‐Butyl Pyridine Additive and Two‐Step Annealing for Efficient CsPbI2Br Perovskite Solar Cells

Phthalimide Additive-Promoted Ambient Fabrication of Inorganic CsPbI2Br Perovskite for Highly Efficient and Stable Solar Cells

Suppressing the Defects in CsPbI2Br Perovskite Photovoltaic Films Via a Homogeneous Cap-Mediated Annealing Strategy

Multistrategy Toward Highly Efficient and Stable CsPbI 2 Br Perovskite Solar Cells Based on Dopant‐Free Poly(3‐Hexylthiophene)

Tri‐Brominated Perovskite Film Management and Multiple‐Ionic Defect Passivation for Highly Efficient and Stable Solar Cells

Illumination Enhanced Crystallization and Defect Passivation for High Performance CsPbI3 Perovskite Solar Cells by Sacrificing Dye

Suppressing the Defects in CsPbI 2 Br Perovskite Photovoltaic Films via a Homogeneous Cap-Mediated Annealing Strategy

Tailoring of CsPbIBr2 Perovskite Crystallization Via Phenylthiourea for Stable and Efficiency Perovskite Solar Cells

Crystallization Management of CsPbI2Br Perovskites by PbAc2-incorporated Twice Spin-Coating Process for Efficient and Stable CsPbI2Br Perovskite Solar Cells

Manipulated Crystallization and Passivated Defects for Efficient Perovskite Solar Cells via Addition of Ammonium Iodide

Dual‐doping Strategy of Metal Chlorides in Ambient Air with High Humidity for Achieving Highly Air‐Stable All‐inorganic Perovskite Solar Cells

Controllable Perovskite Crystallization via Antisolvent Technique Using Chloride Additives for Highly Efficient Planar Perovskite Solar Cells

Bifunctional Lewis Base‐Assisted Fabrication of High‐Quality CsPbIBr2 Perovskite for Efficient and Stable Solar Cells

Indium-Doped CsPbI2.5Br0.5 with a Tunable Band Structure and Improved Crystallinity for Thermo-Stable All-Inorganic Perovskite Solar Cells

Hierarchically Manipulated Charge Recombination for Mitigating Energy Loss in CsPbI 2 Br Solar Cells

Rapid Nucleation and Slow Crystal Growth of CsPbI3 Films Aided by Solvent Molecular Sieve for Perovskite Photovoltaics

Mitigating deep-level defects through a self-healing process for highly efficient wide-bandgap inorganic CsPbI3-xBrx perovskite photovoltaics

Photovoltaic Performance Improvement of All‐Inorganic CsPbBr3 Perovskite Solar Cells by Antisolvent Assisted Crystallization