Abstract:A common phenomenon of polymer solar cells with metal oxide electron-transport layers (ETLs), known as "light-soaking" issue, is that the as-prepared device exhibits an anomalous S-shaped J-V characteristic, resulting in an extremely low fill factor (FF) and thus a poor power conversion efficiency. However, the S-shape disappears upon white light illumination with UV spectral components, meanwhile the performance parameters of the device recover the normal values eventually. This behavior appears to be of general validity for various metal oxide layers regardless of the synthesis and fabricating processes. Its origin is still under debate, while the ETL interface problems have generally been claimed to be the underlying reason so far. In this paper, both conventional and inverted cells with using ZnO nanoparticles (NPs) as ETL are fabricated to clarify the interface effect of the ETL on the light soaking procedure. The inverted device shows a typical light-soaking issue with an initial FF less than 20% as expected, whereas the J-V curves of the conventional cell remain regular shapes throughout the test. This result indicates that the ITO/ZnO interface is a key reason of S-shaped J-V characteristics, which is further verified via the use of Cs2CO3/ZnO ETL. The insert of Cs2CO3 layer isolates the ITO electrode from contacting with ZnO layer, and the kink disappears in the as-prepared device with this bi-layered ETL inverted structure. Our explanation for the result above is that the oxygen impurities absorbed onto the surface of ZnO NPs during fabrication process, behave as strong electron traps, and thus increasing the width of the energy barrier (EB) at the interface of ITO/ZnO. Subsequently, photogenerated electrons accumulate in the ZnO layer adjacent to the interface, resulting in extremely poor performance. Upon white light illumination, however, the trap sites are filled by photogenerated carriers within the ZnO layer, and therefore narrowing the EB. As the barrier width becomes thin enough to be freely tunneled through, a good selectivity behavior of ZnO ETL is reached, leading to a fully remarkable recovery in device performances.

The effect of ZnO preparation on the performance of inverted polymer solar cells under one sun and indoor light

Effect of Electron Collecting Metal Oxide Layer in Normal and Inverted Structure Polymer Solar Cells

Effects of ZnO Fabricating Process on the Performance of Inverted Organic Solar Cells

Influence of ZnO Interlayer on the Performance of Inverted Organic Photovoltaic Device

Effects of the Morphology of A Zno Buffer Layer on the Photovoltaic Performance of Inverted Polymer Solar Cells

Manipulation of Zinc Oxide with Zirconium Doping for Efficient Inverted Organic Solar Cells

Electrical and Optical Properties of Zno Processed by Atomic Layer Deposition in Inverted Polymer Solar Cells

Inverted Organic Photovoltaic Cells with Solution-Processed Zinc Oxide As Electron Collecting Layer

The Effect of Modified Layers on the Performance of Inverted ZnO Nanorods/meh-Ppv Solar Cells

Effect of Crystallinity Modulation Between Electron Transport Layer and Photo‐Generation Materials on ZnO‐Based Polymer Solar Cells

Effect of Zno Electron-Transport Layer on Light-Soaking Issue in Inverted Polymer Solar Cells

Correlating Annealing Temperature of ZnO Nanoparticle Electron Transport Layer with Performance of Inverted Polymer Solar Cells

Low-Temperature Solution-Processed Zno Nanocrystalline Interfacial Layer with Antireflective Effect for Efficient Inverted Polymer Solar Cells

Enhanced Performance And Stability Of Polymer Solar Cells By In Situ Formed Alox Passivation And Doping

Enhanced inverted organic solar cell performance by post-treatments of solution-processed ZnO buffer layers

Inverted Polymer Solar Cells with a Boron-Doped Zinc Oxide Layer Deposited by Metal Organic Chemical Vapor Deposition

Inverted Polymer Solar Cells with a Solution-Processed Zinc Oxide Thin Film As an Electron Collection Layer

Enhanced performance of inverted polymer solar cells by combining ZnO nanoparticles and PFN as electron transport layer.

Metal oxide nanoparticles as an electron-transport layer in high-performance and stable inverted polymer solar cells.

Effect of ZnO-processing Methods on Device Performance and Stability of Effective Inverted Solar Cells

Enhanced Performance of Polymer Solar Cell with Zno Nanoparticle Electron Transporting Layer Passivated by in Situ Cross-Linked Three-Dimensional Polymer Network