Abstract:This research examines the potential of a synthetic e-diesel and oxymethylene dimethyl ether blend in a heavy-duty single-cylinder engine. The main purpose is to find the optimal engine settings that maximize engine efficiency and minimize emissions. As the first step, a methodology was developed and applied to simplify the engine's map into five characteristic points to be representative of the World Harmonized Transient Cycle, assigning weights to each load region. This simplification reported low error estimations for fuel consumption and NOx emissions over the cycle. After obtaining the five points, a drop-in analysis was assessed, where the fuel was evaluated with the same settings as diesel, revealing more advanced and shorter combustion with great reductions in soot emissions. Then, a group of three air management and three injection parameters was selected for optimization. A novel methodology combining Taguchi Design and Response Surface Methodology is developed and applied to find the best engine settings. By integrating these two methods, the research reduced the number of required experiments if only one method were used and maintained the goal of achieving higher thermal efficiencies with the new fuel blend compared to the diesel baseline. Significant statistical results were obtained in the Taguchi design, revealing the air management factors that most affected the responses; meanwhile, second-order models with high accuracy helped in finding the best injection parameters. Subsequently, the best settings were experimentally evaluated, and optimal conditions determined by the two methods were validated, confirming the effectiveness of the methodology. Optimization results revealed an improvement of around 2% higher efficiencies for the five tested points while achieving important average reductions of 28% less in NOx with additional decreases in CO, HC, and soot levels, all outperforming traditional diesel benchmarks. Finally, a well-to-wheel analysis using the simplified cycle confirmed a substantial reduction in carbon impact when replacing diesel with this alternative fuel. The successful application of this methodology to recalibrate an engine with an alternative fuel blend shows the potential of using these fuels in existing engines and offers a novel methodology that can be escalated and applied under the engine calibration context.

Optimization of diesel injection timing, producer gas flow rate, and engine load for a diesel engine operated on dual fuel mode at a high engine speed

Optimisation of an experimental and feasibility research on a CRDI diesel engine based on a blend of waste cooking oil and waste plastic oil using RSM: A value addition for disposed waste oil

Numerical and optimization modeling of dual-fuel natural gas–diesel engine at the idle load

Integrated optimization of common rail direct injection diesel engine input parameters with linseed biodiesel: A hybrid approach using grey relational analysis and genetic algorithm techniques

Performance analysis and optimization of thermal barrier coated piston diesel engine fuelled with biodiesel using RSM

Multiple response optimizations to improve performance and reduce emissions of Argemone Mexicana biodiesel-diesel blends in a VCR engine

Optimization of a diesel/natural gas dual fuel engine under different diesel substitution ratios

Optimization methodology combining Taguchi design and response surface method to maximize a compression ignition engine efficiency fueled with oxygenated synthetic fuel

The Influence of Diesel–Ethanol Fuel Blends on Performance Parameters and Exhaust Emissions: Experimental Investigation and Multi-Objective Optimization of a Diesel Engine

Predict the characteristics of diesel engine using glycine max oil biofuel

Combustion exhaust release impact, diesel engine performance, and optimization studies of green diesel-petrodiesel blend in a high compression ratio direct-injection compression-ignition engine

Prediction and optimization of engine characteristics of a DI diesel engine fueled with cyclohexanol/diesel blends

A study on the performance and emission of diesel engine with Jatropha biodiesel and its blends at different engine load

Optimization of biodiesel/2-propanol/1-hexanol blends based on diesel engine performance using combined mixture-process design (CMPD)

Prediction of emissions and performance of a gasoline engine running with fusel oil–gasoline blends using response surface methodology

Multi-objective RSM-based optimization of diesel-diethyl ether blends in diesel engine to achieve sustainable development goals

Diesel engine operational and emissions attributes optimization through Taguchi–Grey experiment design: exploring the impact of Al2O3–CNT impregnated orange peel biodiesel–diesel blend fuel

Experimental Analysis of Hydrogen Addition at Varying Injection Opening Pressures on a Dual-Fuel Diesel Engine Operating with Diesel and Cottonseed Oil

Determination of Optimum Operating Parameters in a Non-Road Diesel Engine Fueled with 1-Heptanol/Biodiesel at Different Injection Pressures and Advances

Analysis and Optimization of Operational and Pollutant Attributes of Diesel Engine with CNT-Infused Orange Peel Biodiesel-Diesel Blend Fuel

Experimental investigation and optimization of dual fuel combustion using diesel/gasoline and Bio-oil extracted from Co-thermal liquefaction of paint/biomass wastes: An approach towards waste to energy