Abstract:Lithium-rich layered oxides have attracted much attention due to their high discharge capacity (>250 mA h·g–1). However, lithium-rich layered cathodes suffer from poor rate capabilities and voltage decay, which seriously limit their practical application. Herein, a unique @spinel double-spinel shell heterostructure is designed and successfully synthesized via coprecipitation and high-temperature solid-phase methods. In particular, lithium-rich layered oxides show good rate capabilities and high capacity retention when the molar amount of cobalt acetate and manganese acetate is 5%. After 100 cycles at 0.2 C, a discharge capacity of 232 mA h g–1 and a capacity retention of 92.7% can be obtained. The superior electrochemical performance of the in situ-transformed Li-rich layered cathode can be attributed to the unique three-dimensional diffusion channels for Li ions of the surface spinel phase. Besides, the in situ-transformed LiCoMnO4 shell can also improve the structural stability of the Li-rich layered oxides by reducing the side reactions and protecting the material from being corroded by the electrolyte. This study provides a strategy for surface modification, which can effectively improve the electrochemical performance of Li-rich layered cathode materials with high performance.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.1c01955.SEM image of the precursor Ni1/6Co1/6Mn4/6CO3 and the corresponding mapping spectrum; ex situ XRD spectra of the LLO and LSS-0.05 samples; EDS line scan of the selected area and the corresponding HTEM diagram of the LSS-0.05 sample; CV and dQ/dV curves of the first three cycles of the LLO, LSS-0.05, and LSS-0.1 samples; initial charge and discharge curves of LiCoMnO4, LSS-0.2, and LSS-0.4 samples; discharge curves of LLO, LSS-0.05, and LSS-0.1 samples at different rates and with different cycles; typical single titration curve of GITT measurements; equivalent circuit of half-cells; and EIS spectra of LLO, LSS-0.05, and LSS-0.1 samples in the initial cycle (PDF)This article has not yet been cited by other publications.

SeO 2 -infused grain boundaries effectively improve rate and stability performance of Li-rich manganese-based layered cathode materials

Enhanced Electrochemical Performance of Li1.2Mn0.54Ni0.13Co0.13O2 Cathode Material Coated with Li+-conductive Li2SiO3 for Lithium Ion Batteries

Interfacial Lithiation Induced Leapfrog Phase Transformation in Carbon Coated Se Cathode Observed by In-Situ TEM

Radially Oriented Single‐Crystal Primary Nanosheets Enable Ultrahigh Rate and Cycling Properties of LiNi0.8Co0.1Mn0.1O2 Cathode Material for Lithium‐Ion Batteries

π-type orbital hybridization and reactive oxygen quenching induced by Se-doping for Li-rich Mn-based oxide cathode

Oxygen Release Suppression and Electronic Conductivity Enhancement for High Performance Li‐ and Mn‐Rich Layered Oxides Cathodes by Chalcogenide Redox Couple and Oxygen Vacancy Generations

Improving rate capacity and cycling performance of lithium-rich high-Mn Li-1.8[Mn0.7Co0.15Ni0.15]O-2.675 cathode materials by Li2SiO3 coating

MoSe 2 @CNT Core–Shell Nanostructures as Grain Promoters Featuring a Direct Li 2 O 2 Formation/Decomposition Catalytic Capability in Lithium‐Oxygen Batteries

Invoking Interfacial Engineering Boosts Structural Stability Empowering Exceptional Cyclability of Ni‐Rich Cathode

Multifunctional surface structure with enhanced electron and ion conductivities for superior electrochemical performance of Co-free Li-rich Mn-based layered oxide cathodes

Improving the Electrochemical Performance of a Lithium-Rich Layered Cathode with an In Situ Transformed Layered@Spinel@Spinel Heterostructure

Significant Enhancement of the Capacity and Cycling Stability of Lithium-Rich Manganese-Based Layered Cathode Materials via Molybdenum Surface Modification

Preparation of Single-Crystal Li-Rich Mn-Based Layered Oxides with Excellent Electrochemical Performance via Simple Stepwise High-Temperature Sintering

In-situ formation of Li0.5Mn0.5O coating layer through defect controlling for high performance Li-rich manganese-based cathode material

One-pot synthesis and multifunctional surface modification of lithium-rich manganese-based cathode for enhanced structural stability and low-temperature performance

Regulating Interfacial Compositions to Build a Stable Superlattice Structure of Layered Oxide Cathode Materials for Sodium-Ion Batteries

Enhancement structural stability of LiNi0.8Co0.1Mn0.1O2 via S2− doping combine with Li2SO4 coating co-modification

Effect of SiO2 Coating on Microstructure and Electrochemical Properties of LiNi0.5Mn1.5O4 Cathode Material

Tuning Li2MnO3-Like Domain Size and Surface Structure Enables Highly Stabilized Li-Rich Layered Oxide Cathodes.

Enhanced cycling stability of Li[Li0.2Mn0.54Ni 0.13Co0.13]O2 by surface modification of MgO with melting impregnation method

Surface Doping to Enhance Structural Integrity and Performance of Li‐Rich Layered Oxide