Abstract:Welding processing is an important method to connect precision component, but the internal stress and crystal anisotropy reduce its performance, which are difficult to solve due to the specific demand on regional post-treatment. In the present research, the asynchronized laser shock peening (ALSP) and synchronized laser shock peening (SLSP) processing technologies were applied to treat the laser joined Ti-6Al-4V thin plates. The microstructure and mechanical properties of the as-welded joint, ALSP and SLSP processed joint were investigated. The results revealed that the as-welded joint presents obvious anisotropic characteristics, and high strain level exists on the prior β grain boundary, which causes stress concentration. The ultimate tensile strength (UTS) and elongation (EL) values of as-welded joint just reach the 92.18% and 72.33% of as-received plate, respectively. ALSP processing could result in the deformation with the depth more than ten microns and introduce compress stress in the top layer, but has little effect on decreasing the anisotropy. The grain boundary becomes obscure and the strain distribution is relatively uniform, accompanying with some dynamic recrystallized laths exist along the grain boundary. Its values of UTS and EL are 5.23% and 5.59% higher than as-welded joint, respectively. With the SLSP processing, the deformation depth exceeds twenty microns, and the crystal isotropy could be greatly promoted. Moreover, higher compressive stress is introduced from top layer to center area of joint. The grain boundary becomes obviously obscure, which is completely replaced by recrystallized lath structures. The residual strain in the top layer is partly eliminated, and the stress concentration phenomenon along grain boundary is dramatically decreased. The UTS and EL values are 6.16% and 20.58% higher than as-welded joint, and reach 97.86% and 87.22% of as-received plate, respectively.

Influence of surface pretreatment of steel substrate on the interfacial microstructure and tensile properties of laser Al/steel joints

Toward understanding the fractured mechanism in laser welded–brazed Al/steel interface by in–situ SEM tensile observations

Effect of heat input on interfacial microstructure, tensile and bending properties of dissimilar Al/steel lap joints by laser Welding-brazing

In situ SEM study on tensile fractured behavior of Al/steel laser welding-brazing interface

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Interfacial microstructure and strengthening mechanism of dissimilar laser al/steel joint via a porous high entropy alloy coating

Effect of asynchronized and synchronized laser shock peening on microstructure and mechanical properties of the Ti-6Al-4V laser joint

Tensile resistance, microstructures of intermetallic compounds, and fracture modes of welded steel/aluminum joints produced using laser lap welding

Influence of Alloy Elements on Microstructure and Mechanical Properties of Al/steel Dissimilar Joint by Laser Welding/brazing

Experimental and theoretical studies on laser treatment strategies for improving shear bonding strength of structural adhesive joints with cast aluminum

Effect of defocusing distance on interfacial reaction and mechanical properties of dissimilar laser Al/steel joints with a porous high entropy alloy coating

Microstructure and Mechanical Properties of Pulsed Laser Welded Al/steel Dissimilar Joint

Effect of laser pre-treatment on adhesive joint performance and evaluation of interfacial strain distribution using mechanoluminescence

First-principles and experimental investigations on ductility/brittleness of intermetallic compounds and joint properties in steel/aluminum laser welding

Evolution mechanism of interfacial microstructure and regulation of mechanical properties of laser-arc hybrid weld-brazing aluminum/steel joints under different post-welding heat-treatment temperatures

Microstructural, Porosity and Mechanical Properties of Lap Joint Laser Welding for 5182 and 6061 Dissimilar Aluminum Alloys under Different Place Configurations

Effect of grain orientation on microstructure and mechanical properties of laser welded joint of additive manufactured 300M steel

Experimental and Theoretical Investigation of Laser Pretreatment on Strengthening the Heterojunction Between Carbon Fiber Reinforced Plastic and Aluminum Alloy.

Influence of processing window on laser welding-brazing of Al to press-hardened 22MnB5 steel

First principle calculations and mechanical properties of the intermetallic compounds in a laser welded steel/aluminum joint

Research on Welding Quality Optimization of Ultra-High Strength Steel Welding Joint Under Different Laser Energy Inputs