Abstract:During the past years, the power conversion efficiency (PCE) of perovskite solar cells (PSCs) has increased from 3.8% to 25.7%, making them the best candidate for the next-generation photovoltaic devices. Two dominant PSC architectures have evolved, a regular n-i-p structure with mesoscopic or planar heterojunction and an inverted p-i-n planar structure. Compared to the regular n-i-p PSCs, the inverted p-i-n PSCs possess the advantages of lower synthesis temperature, no hysteretic effect and good compatibility with the tandem solar cells. For p-i-n PSCs, the hole transport layer (HTL) determines the hole transport efficiency and crystallinity of perovskite, so it plays a crucial role in the stacked devices. The conventional organic HTL of PEDOT:PSS-based PSCs can achieve satisfying PCEs, but may be able to impede the commercialization of perovskite photovoltaic devices because of their high price and acidity-induced poor stability. By comparison, the inorganic P-type NiOx with wide band gap exhibits low cost, superior chemical stability and high hole mobility without corrosion to perovskite layer. Unlike the most reported spin-coated NiOx nanoparticle films, we used sputtered NiOx as HTL for application in FA-based PSCs and achieved a PCE of 20.05%. After systematically optimizing the sputtering parameters, including power, time and argon flow rate, we obtained better crystal quality, better transparency, proper energy level, and higher hole mobility of NiOx film. Reducing the interstitial vacancies and defects in NiOx films attributes to decreased nonradiative recombination losses, which mainly cause the hole accumulation near the perovskite/NiOx interface. Finally, a champion device with open-circuit voltage (Voc) of 1.09 V, current density (Jsc) of 23.4 mA/cm 2 , fill factor (FF) of 78% and PCE of 20.05% are obtained. This work has important significance for preparation of large-area perovskite solar cell modules.

Highly crystalline colloidal nickel oxide hole transport layer for low-temperature processable perovskite solar cell

Printable and Homogeneous NiO x Hole Transport Layers Prepared by a Polymer‐Network Gel Method for Large‐Area and Flexible Perovskite Solar Cells

Room-Temperature and Solution-Processable Cu-Doped Nickel Oxide Nanoparticles for Efficient Hole-Transport Layers of Flexible Large-Area Perovskite Solar Cells

Syntheses of efficient nickel oxide film by low-temperature fabrication technique for high-performance perovskite solar cells

High-efficiency perovskite solar cell using cobalt doped nickel oxide hole transport layer fabricated by NIR process

NiOx Nanocrystals with Tunable Size and Energy Levels for Efficient and UV Stable Perovskite Solar Cells

Room-Temperature-Sputtered Nanocrystalline Nickel Oxide as Hole Transport Layer for p–i–n Perovskite Solar Cells

Doping Free and Amorphous NiO x Film via UV Irradiation for Efficient Inverted Perovskite Solar Cells

Preparation of Nickel Oxide Nanoflakes for Carrier Extraction and Transport in Perovskite Solar Cells

Low-temperature water-processed NiO hole transport layers for high-efficiency CH3NH3PbI3 perovskite solar cells

Sputtered Niox Films As Hole Transport Layers for FA-Based Perovskite Solar Cell Application

The Effect of Different Precursor Solutions on the Structural, Morphological, and Optical Properties of Nickel Oxide as an Efficient Hole Transport Layer for Perovskite Solar Cells

Metal organic framework derived NiO x nanoparticles for application as a hole transport layer in perovskite solar cells

Electrical and Optical Properties of Nickel‐Oxide Films for Efficient Perovskite Solar Cells

Oxidized Nickel to Prepare an Inorganic Hole Transport Layer for High-Efficiency and Stability of CH3NH3PbI3 Perovskite Solar Cells

Printable oil-NiOX hole transport layer enables efficient n-i-p perovskite solar cells with a high thermal stability

Low-Temperature Chemical Bath Deposition of Conformal and Compact NiOX for Scalable and Efficient Perovskite Solar Modules

Nickel Oxide for Perovskite Photovoltaic Cells

Tailoring of Ligand‐Off Nanoparticles Inks for Thin p‐Type Oxide Overlayers Formation with Maintaining Intact Halide Perovskite

Surface Modification of NiO Nanoparticles for Highly Stable Perovskite Solar Cells Based on All-Inorganic Charge Transfer Layers

Vacancy defect modulation in hot-casted NiO film for efficient inverted planar perovskite solar cells