Abstract:Nowadays, consumer trends towards healthier and low fat products have a significant impact on the deep fat frying industry. The objective of this study was to design a modified deep fat fryer (MDF) to have a smaller surface area relative to height, with made a steam blanketing over the fryer. Different levels of water injection flow rates have been used (0.1, 0.2 and 0.3 ml/20 min. per 1 liter of tested oil), compared with conventional fryers (CDF). Frying was conducted at 170 ± 10 °C into sunflower oil using CDF (H√A = 0.24) and MDF (H√A = 0.8) in batch 8 min. 16 batches every day (eight hrs. /day)for up to 40 hrs (Consecutive five days). The modification was intended to related oil deterioration. Water injection had a dual effect. In comparison with CDF, water injection increased the acidity (expressed as oleic acid) from 0.34 % to 0.97 %, after 40 hrs at 170 ± 10 °C of deep fat frying, and a contrarily, the protective role was observed in all the other quality indices. Significant reductions in TBA values (from 8.9 to 4.81mg malonaldehyde/liter of tested oil), P-anisidine values (from 35.6 to 12.9), TPC contents (from 34.5% to 18.64%), conjugated diene (232 nm) (from 8 to 5.59) and conjugated triene (268 nm) (from 1.9 to 1.33) were recorded in sunflower oil compared with CDF. These quality indices of sunflower oil developed dramatically in the first level of water injection flow rate. Consequently, the first level of water injection had the highest (P≥0.05) inhibitory effect compared with the other levels of water injection. Fatty acid composition of fried oil properties during deep frying CDF and MDF designs were determined. There were significant differences (P≥0.05) of fatty acids composition between the fried oil induces during using of CDF and MDF designs. Total unsaturated fatty acid at MDF design gave the highest values. Also, organoleptic evaluation of fried potato chips by CDF and MDF were evaluated by panelists. Fried potato chips during the first level of water injection flow rate had the highest (P≥0.05) flavor (4), crisp (4.5), greasiness (4.6), and overall acceptability (4.8), compared with fried potato chips during other levels of water injection flow rates and with CDF. Findings suggest that determination of the oil quality indices are good makers of sensory evaluation during deep fat frying. Results indicated the changes in moisture content, oil uptake and shrinkage percentages of potato chips at different levels of water injection compared the control samples. The negative correlation coefficient between oil uptake and moisture content was high (r = -0.915) and linear regression equation for prediction the oil uptake y = 34.1064 – 2.0291X. Also, results suggest that during deep fat frying by MDF design may reduce the thermal deterioration of sunflower oil. Water injection can be applied as a simple method to improve oil quality during deep fat frying.

Two-phase (solid–fluid) coupled transfer phenomena modeling during frying of potato slices: Effect of the product surface-to-volume ratio

Multiphase flow, heat and mass transfer modeling during frying of potato: effect of food sample to oil ratio

Simulation of Heat Transfer in Deep Fat Frying of Foods: an Appropriate Method for Predicting the Temperature Distribution in a Potato Model

Dual-Stage ultrasound in deep frying of potato chips; effects on the oil absorption and the quality of fried chips

Evaporation front compared with crust thickness in potato deep-fat frying

Heat and Mass Transfer Modeling to Predict Temperature Distribution during Potato Frying after Pre-Treatment with Pulsed Electric Field

Predicting lift-off time when deep-frying potato dough snacks

A review on heat and mass transfer coefficients during deep-fat frying: Determination methods and influencing factors

Influence of a three stage hybrid ultrasound-osmotic-frying process on production of low-fat fried potato strips.

Modeling of heat and mass transfer processes at frying barley grain with superheated steam

Standardization of domestic frying processes by an engineering approach

Influence of steam singlet method on oil quality during deep fat frying on a modified fryer

A fully coupled multiphase model for infrared-convective drying of sweet potato

Mass-Transfer Simulation Software Study of Sliced Porous Production During Convection Drying Process

The analysis of heat and mass transfer during frying of food using a moving boundary solution procedure

Effect of Combined Ultrasound-assisted Osmotic Dehydration with Edible Coatings on Mass Transfer of Fried Kiwi Fruit Disks

Determination of heat and mass transfer parameters during frying of potato slices

Impact of deep-fat frying cycles on the physicochemical characteristics of two edible vegetable oils marketed in Algeria

Modelling the Mass Transfer Kinetics of Battered and Breaded Fish Nuggets during Deep-Fat Frying at Different Frying Temperatures

Multi-agent simulation of doughnut deep fat frying considering two domain heating media and sample flipping