Abstract:Cities around the world are exposed to increasing heat stress as a result of the heat island effect exacerbated by extreme weather events, population growth and increased urbanization. To promote outdoor activities and protect human health, there is an urgent need for a tool to assess the outdoor thermal environment. While the air temperature ( T a ) and relative humidity (RH) are usually available from weather stations, but the mean radiant temperature (MRT) cannot. The MRT is a key variable in determining outdoor thermal comfort. Therefore, it is necessary to develop a simple and accurate method for calculating MRT, in order to compute the corresponding thermal indices, which can be used to assess the thermal environment more accurately. This study was conducted at a university in Guangzhou, China. Four different ground-cover surfaces (concrete, asphalt, lawn, and granite) were selected for study. The T a , black-globe temperature ( T g ), long-wave ( L ), and short-wave ( K ) radiation in six directions, and wind speeds ( V a ) were measured under unshaded conditions. The MRT obtained by the six-direction integral method was used as the base value and regression analyses were performed with T a , K ↓ (downward short-wave), and V a . In addition, the six indices—significance ( P ), linear regression coefficient ( R 2 ), consistency index ( d ), root mean square error (RMSE), mean bias error (MBE), and mean absolute error (MAE)—were used for quantitative analysis to explore the feasibility of this method. This study compared five calculation models on MRT: MRT SDIM (six-direction integral method), MRT BGTM-Va-0.1Hz (black-globe thermometer method, 0.1 Hz wind speed measurement frequency), MRT BGTM-Va-10Hz (black-globe thermometer method, 10 Hz wind speed measurement frequency), MRT BGTM-P (polynomial regression based on black-globe thermometer method), and MRT SDIM-P (polynomial regression based on six-direction integral method). The MRT SDIM was used as a baseline value, and the values obtained by other four methods were discussed and validated separately. The results show that the calculation model about MRT SDIM-P has a relatively minimal error with the values ≤ 5 °C, which satisfies the accuracy requirements for thermal stress. Finally, the data from each area weather station were substituted into the model and compared with the actual measurement days, and the monthly mean and maximum universal thermal climate index (UTCI) were calculated for the entire Guangzhou daytime in 2022. The results obtained from the weather station data calculations fit well with the measured data. Consequently, this study provides a simple method of calculation for outdoor mean radiant temperature. Further, based on the calculated thermal indices, recommendations can be provided for outdoor work and activities.

Comparison and modification of measurement and simulation techniques for estimating Tmrt in summer and winter in a severely cold region

Assessment of the estimation methods of Tmrt in semi-outdoor spaces in humid sub-tropical climates: An empirical study in Wuhan, China

Estimation of mean radiant temperature across diverse outdoor spaces: A comparative study of different modeling approaches

Improved methods for estimating mean radiant temperature in hot and sunny outdoor settings

Comparison of different methods of estimating the mean radiant temperature in outdoor thermal comfort studies

Developing a method for calculating the mean outdoor radiant temperature for thermal stress in Guangzhou

TWO METHODS FOR REMOTE ESTIMATION OF COMPLETE URBAN SURFACE TEMPERATURE

Atmospheric sensitivity on land surface temperature retrieval using single channel thermal infrared remote sensing data: Comparison among models

Intercomparison of methods for estimating land surface temperature from a Landsat-5 TM image in an arid region with low water vapour in the atmosphere

Remote estimation of complete urban surface temperature using only directional radiometric temperatures

Modeling Mean Radiant Temperature Distribution in Urban Landscapes Using DART

Intra-urban Differences of Mean Radiant Temperature in Different Urban Settings in Shanghai and Implications for Heat Stress under Heat Waves: A GIS-based Approach

Higher accuracy estimation of the weighted mean temperature (Tm) using GPT3 model with new grid coefficients over China

Evaluation of Brightness Temperature Sensitivity to Snowpack Physical Properties Using Coupled Snow Physics and Microwave Radiative Transfer Models

A New Empirical Model of Weighted Mean Temperature Combining ERA5 Reanalysis Data, Radiosonde Data, and TanDEM-X 90m Products over China

The improvement and comparison of diffuse radiation models in different climatic zones of China

Satellite-based estimation of monthly mean hourly 1-km urban air temperature using a diurnal temperature cycle model

Comparison of Nighttime Land Surface Temperature Retrieval Using Mid-Infrared and Thermal Infrared Remote Sensing Data Under Different Atmospheric Water Vapor Conditions

Evaluation of the weighted mean temperature over China using multiple reanalysis data and radiosonde

Simplifying the Revised Three-Temperature Model for Remotely Estimating Regional Evapotranspiration and Its Application to A Semi-Arid Steppe

An analytical urban temperature model with building heterogeneity using geometric optical theory