Abstract:Hybrid plasma spraying combines plasma spraying of dry coarse powders and liquids (suspensions or solutions) potentially providing high deposition rates and coatings with novel microstructures and amended functionality. Such composites may be potentially interesting also for the thermal barrier coatings (TBCs). In this study, the first experimental TBCs with hybrid ceramic top-coats were deposited by hybrid water-/argon-stabilized plasma (WSP-H) technology. Coarse dry YSZ (yttria-stabilized zirconia: ZrO 2 -Y 2 O 3 ) powder was selected to form the top-coat matrix. Suspensions of YSZ, Al 2 O 3 (alumina), YAG (yttrium aluminum garnet: Y 3 Al 5 O 12 ), or GZO (gadolinium zirconate: Gd 2 Zr 2 O 7 ) were the source of the additional miniature phase. Uniform functionalized coatings with TBC-relevant thickness and microstructure were successfully deposited. Hybrid and reference coatings deposited also with WSP-H torch and with YSZ feedstocks showed comparable thermal diffusivity regardless of the spraying conditions but the addition of Al 2 O 3 and YAG increased it by ~ 65%, whereas GZO decreased it by ~ 20%. Thermal cycling resistance of the coatings was evaluated by thermal cycling fatigue (TCF) test. Hybrid coating with the addition of YSZ miniature phase endured on average 640 TCF cycles, which was 250-300 cycles less than the reference YSZ coatings deposited without liquid feedstocks but still comparable to the currently used YSZ-based industrial TBCs. Coatings with dissimilar chemistry of additional miniature splats showed inferior mean TCF lifetimes: GZO 438 cycles, Al 2 O 3 272 cycles, and YAG 173 cycles, opening space for further coating optimization. All hybrid coatings failed above the bond-coat/top-coat interface. Comparison of coatings before and after the thermal exposure by scanning electron microscopy (SEM) and x-ray diffraction (XRD) revealed possible changes within the coating microstructure, namely sintering (typical for top-coat consisting only of YSZ), conversion of metastable and amorphous phase (top-coats with the addition of Al 2 O 3 and YAG) or interaction between the matrix and secondary phase (top-coat with the addition of GZO).

Concentrated Solar Power Testing of Plasma-Sprayed Hybrid Thermal Barrier Coatings

Experimental and Simulation Study of Mn–Fe Particles in a Controllable-Flow Particle Solar Receiver for High-Temperature Thermochemical Energy Storage

Microstructure and Thermal Properties of the Early-Stage Experimental Thermal Barrier Coatings Deposited by Hybrid Plasma Spraying

CMAS Infiltration Behavior of Atmospheric Plasma-Sprayed Thermal Barrier Coating with Tailored Pore Structures

Low Thermal Conductivity Yttrium Aluminum Garnet Thermal Barrier Coatings Made by the Solution Precursor Plasma Spray: Part II—Planar Pore Formation and CMAS Resistance

Multilayer GZ/YSZ Thermal Barrier Coating from Suspension and Solution Precursor Plasma Spray

In Situ Monitoring of Cracking Mechanisms in Multi-Layered Suspension Plasma-Sprayed Thermal Barrier Coatings

Investigating the Cmas Corrosion Resistance and Thermal Cycling Failure Behavior of Porous Thermal Barrier Coatings with Different Morphologies Prepared by Plasma Spraying

Molten CMAS resistance strategy for PS-PVD TBCs based on laser textured and Al-modified bionic structure

Plasma-Sprayed Thermal Barrier Coatings with Enhanced Splat Bonding for CMAS and Corrosion Protection

Numerical Assessment of Thermal Insulation and Stress Responses in Film-Cooled Turbine Vane Thermal Barrier Coatings under CMAS Deposition Conditions

Practical Aspects of Suspension Plasma Spray for Thermal Barrier Coatings on Potential Gas Turbine Components

Thermal Cycling Test of Solar Salt in Contact with Sustainable Solid Particles for Concentrating Solar Power (CSP) Plants

Fine-Lamellar Structured Thermal Barrier Coatings Fabricated by High Efficiency Supersonic Atmospheric Plasma Spraying

Exploring the Crack Propagation Behavior in Suspension Plasma Sprayed Thermal Barrier Coatings: an In-Situ Three-point Bending Study in Scanning Electron Microscope

Sintering resistance of advanced plasma-sprayed thermal barrier coatings with strain-tolerant microstructures

Integrating APS TBCs with a built-in Al2O3 protection network for superior CMAS resistance

Present status and future prospects of plasma sprayed multilayered thermal barrier coating systems

High Temperature In-Situ Synchrotron X-Ray Diffraction Technique of Thermal Barrier Coatings under Thermal Gradient and Mechanical Loads

Tracking the Calcium-Magnesium-alumino-silicate (CMAS) Infiltration into an Air-Plasma Spray Thermal Barrier Coating Using X-ray Imaging

Thermal Fatigue of Atmospheric Plasma Sprayed Thermal Barrier Coatings