Abstract:Non-fullerene electron acceptors have attracted enormous attention of the research community owing to their advantages of optoelectronic and chemical tunabilities for promoting high-performance polymer solar cells (PSCs). Among them, fused-ring electron acceptors (FREAs) are the most popular ones with the good structural planarity and rigidity, which successfully boost the power conversion efficiencies (PCEs) of PSCs to over 14%. In considering the cost-control of future scale-up applications, it is also worthwhile to explore novel structures that are easy to synthesize and still maintain the advantages of FREAs. In this work, we design and synthesize a new electron acceptor with an unfused backbone, 5,5'-((2,5-bis((2-hexyldecyl)oxy)-1,4-phenylene)bis(thiophene-2-yl))bis(methanylylidene)) bis(3-oxo-2,3-dihydro-1H-indene-2,1-diylidene))dimal-ononitrile (ICTP), which contains two thiophenes and one alkoxy benzene as the core and 2-(3-oxo-2,3-dihydroinden-1-ylidene) malononitrile (IC) as the terminal groups. The synthetic route to ICTP involves only three steps, with high yields. Density functional theory calculations indicate that the non-covalent interactions, O center dot center dot center dot H and O center dot center dot center dot S, help reinforce the space conformation between the central core and the terminals. ICTP shows broad and strong absorption in the long-wavelength range between 500 and 760 nm. The highest occupied molecular orbital and lowest unoccupied molecular orbital levels of ICTP were measured to be -5.56 and -3.84 eV by cyclic voltammetry. The suitable absorption and energy levels make ICTP a good acceptor candidate for medium bandgap polymer donors. The best devices based on PBDB-T:ICTP showed a PCE of 4.43%, with an open circuit voltage (V-OC) of 0.97 V, a short circuit current density (J(SC)) of 8.29 mA.cm(-2), and a fill factor (FF) of 0.55, after adding 1% 1,8-diiodooctane (DIO) as the solvent additive. Atomic force microscopy revealed that DIO could ameliorate the strong aggregation in the blended film and lead to a smoother film surface. The hole and electron mobilities of the optimized device were measured to be 9.64 and 2.03 x 10(-5) cm(2).v(-1).s(-1), respectively, by the space-charge-limited current method. The relatively low mobilities might be responsible for the moderate PCE. Further studies can be performed to enlarge the conjugation length by including more aromatic rings. This study provides a simple strategy to design non-fullerene acceptors and a valuable reference for the future development of PSCs.

Non-fullerene electron acceptors constructed by four strong electron-withdrawing end groups: Potential to improve the photoelectric performance of organic solar cells by theoretical investigations

Rational Design Non-Fullerene Acceptor-Based High Efficiency BHJ Polymer Solar Cells Through Theoretical Investigations

Enhanced crystal network and charge transfer of non-fused ring electron acceptors via interchain interaction for efficient and stable organic solar cells

Unsymmetrically Chlorinated Non-Fused Electron Acceptor Leads to High-Efficiency and Stable Organic Solar Cells.

A Simple Electron Acceptor with Unfused Backbone for Polymer Solar Cells

Nonfullerene Acceptors with Aromatic Heterocycle Substitutions for Efficient Organic Solar Cells

Intrinsically Chemo- and Thermostable Electron Acceptors for Efficient Organic Solar Cells

2D Side‐Chain Engineered Asymmetric Acceptors Enabling Over 14% Efficiency and 75% Fill Factor Stable Organic Solar Cells

A–D–A'–D–A type nonfused ring electron acceptors for efficient organic solar cells via synergistic molecular packing and orientation control

Enhanced Crystal Network and Charge Transfer of Non-Fused Ring Electron Acceptor Via Interchain Interaction Enable Efficient and Stable Organic Solar Cells

Non-fullerene acceptors with alkoxy side chains and different halogenated end groups for efficient organic solar cells

Near-Infrared Electron Acceptors with Unfused Architecture for Efficient Organic Solar Cells.

Optimizing the Molecular Structure of Dithienophthalimide-Based Nonfused Ring Electron Acceptors for Efficient Organic Solar Cells

Regulating Molecular Packing and Orientation of Nonfused Ring Electron Acceptors for Organic Solar Cells with a High Figure‐of‐Merit

Regulating Molecular Packing and Orientation of Non‐Fused Ring Electron Acceptors for Organic Solar Cells with a High Figure‐of‐Merit

Synergistic Interplay between Asymmetric Backbone Conformation, Molecular Aggregation, and Charge-Carrier Dynamics in Fused-Ring Electron Acceptor-Based Bulk Heterojunction Solar Cells

Nonfused Ring Electron Acceptors for Efficient Organic Solar Cells Enabled by Multiple Intramolecular Conformational Locks

Non-fullerene acceptor with asymmetric structure and phenyl-substituted alkyl side chain for 20.2% efficiency organic solar cells

Enhancement Of Intra- And Inter-Molecular Pi-Conjugated Effects For A Non-Fullerene Acceptor To Achieve High-Efficiency Organic Solar Cells With An Extended Photoresponse Range And Optimized Morphology

A 3D nonfullerene electron acceptor with a 9,9′-bicarbazole backbone for high-efficiency organic solar cells

New roles of fused-ring electron acceptors in organic solar cells