Abstract:Introduction. Difficult-to-machine materials with enhanced physical and mechanical properties are increasingly being used in various industries. Such materials are used in mechanical engineering for the manufacture of parts and assemblies of machines and mechanisms, in the production and processing of food products where increased operational requirements are required. In modern production, along with traditional methods of intensifying technological operations, combined and hybrid processing technologies are used. For the finishing of products, abrasive grinding with a diamond tool is used. One of the problems hindering the wide practical application of this method in industry is the fact that it has a high prime cost caused by the cost of materials used in the manufacture and the laboriousness of the tool shaping process. This leads to the need to develop a new technology for manufacturing diamond tools. The purpose of the work is to increase the efficiency of the end diamond abrasive tool with a metal bond by using carbon steels as a body material, increasing the strength of the connection between the body and the diamond-bearing part, as well as choosing an effective tool manufacturing technology. Research methodology. To gain this task, a technology for manufacturing end diamond abrasive tools is developed and tested. Allowing using the technology of capacitor welding to connect the diamond-bearing part with the shank and use medium-carbon hardened high-quality steels with a hardness of 45-60 HRC as the shank material. The strength of the connection of the body with the working diamond-bearing part of the grinding head samples is determined by tensile testing on a 1958U10 tensile machine with maximum load 100 kN. The quality of the joint is assessed visually by the presence of discontinuities in the joint, as well as by examining the microstructure and measuring the microhardness of the weld and heat-affected zones. The microhardness of the welded joint is measured using an HMV-G21ST semi-automatic microhardness tester (Shimadzu, Japan) at a load of 50 g. Results and discussion. Thus, the results of comparative studies allow us to assert that the strength of the connection between the shank and the working diamond-bearing part according to the proposed technology surpasses similar characteristics of the strength of the connection between the shank and the diamond-bearing layer of grinding heads obtained by the method selected by the prototype. Conclusions. The proposed technology for the manufacture of diamond heads increases the strength of the connection between the body and the diamond-bearing working part, reduces the cost of manufacturing the grinding heads due to the use of hardened medium-carbon steels as the material of the tool body instead of high-speed steel grades, the technology is simplified and the possibility of automating the manufacture of tools appears.

Optimization Design of Diamond Circular Saw-Blade with Discontinuous Cutting and Uneven Distribution for Cutting Thin-Walled Tubes

Genetic Algorithm-Based Optimization of the Thin-Walled Tube of High Strength Aluminum Alloy in Diamond Turning Process

Cutting performance of saw blades with microtextured rougher and finisher sawteeth

Research on the cutting performance and contact behavior of a new bionic saw blade segment

Numerical simulation and experiment research on forming of hollow blade with 304 stainless steels and Ti–6Al–4V tubes by sand mandrel

Experimental and Numerical Study on Regulation of Cutting Temperature during the Circular Sawing of 45 Steel

Numerical Simulation of the Laser Welding Process for Diamond Saw Blades

Investigation on the machining performance of copper-based diamond ultra-thin dicing blades manufactured by fused deposition modeling and sintering (FDMS)

Design Optimization Analysis of Venturi Tube for Medium Conveying in Strengthen Grinding Process

Material and processing optimization on disc cutter of tunnel boring machine for failure prevention

Formulation and Implementation of Energy Efficient Ultraviolet Curing for Photosensitive Resin-Bound Diamond Wire Saws

Research on Formation Mechanism and Optimization Method of Surface Waviness of TC4 Blisk Blade

Ultrasonic Vibration-Assisted Cutting of AISI 420 Mod Steel by Using CVD Thick-Film Diamond Tool

An ultrasonic vibration-assisted system development for inner-diameter sawing hard and brittle material

Overcoming challenges: advancements in cutting techniques for high strength-toughness alloys in aero-engines

Dynamics study and damping optimization of circular saw based on numerical simulation and experimental analysis

Improving the efficiency of metal-bonded diamond abrasive end tools by improving manufacturing technology

Enhanced Reconditioning of Heavy-Duty Pulp Industry Equipment

Cutting dynamics research on the five-axis machining of thin curved surface with barrel-taper-ball milling cutter

A Study of Slicing Process with Thin Diamond Wire(Grinding Technology)

Precision Machining by Dicing Blades: A Systematic Review