Abstract:Background Advancements in computer-aided design (CAD) and computer-aided manufacturing (CAM) technology have significantly improved the accuracy and consistency of producing fixed partial dentures (FPDs) compared to traditional manual methods. However, the fully digital transfer of mock-up morphology to final FPDs is not yet fully explored. Proper pontic design, which avoids direct gingival contact, is essential for maintaining oral hygiene and preventing tissue irritation. Aim and objectives This study aims to compare the effectiveness of digital versus manual methods in FPD pontic fabrication, focusing on the trueness of digitally fabricated FPD patterns. Key objectives include assessing thickness, vertical gaps, and anatomical accuracy to determine the advantages of CAD-CAM technologies over traditional techniques. Materials and methods In this in vitro study, a total of 45 FPD pontics were fabricated and divided into three groups (15 each): digitally fabricated (using CAD software and CAM systems), manually fabricated (using traditional wax-up techniques), and a control group (typodont teeth). Tooth preparation was performed on a typodont, and impressions were taken to create casts. One cast was scanned and digitally designed, while the other was used for manual fabrication. Outcome assessments included vertical gap measurement using a stereo microscope, thickness evaluation with a digital caliper, and anatomical similarity assessment by independent evaluators. Statistical analysis involved one-way analysis of variance (ANOVA), post hoc Tukey's analysis, and unpaired t-tests using SPSS software version 26.0 (IBM Inc., Armonk, New York). Statistical significance was set at 0.05. Results The digital group exhibited lower mean thickness at the incisal (1.92±0.130 mm vs. 2.46±0.219 mm for manual, p=0.000), middle (7.00±0.223 mm vs. 8.88±0.983 mm for manual, p=0.001), and cervical sites (9.06±0.134 mm vs. 10.08±0.454 mm for manual, p=0.000). No significant differences were found between the digital and control groups. No significant differences were observed between digital, manual, and control groups at any site (p=0.688 to 0.997). The digital group demonstrated superior accuracy and consistency compared to the control group (mean value of 1.00±0.00 vs. 2.93±0.798, p=0.000). Conclusion CAD-CAM technology greatly improves the precision and consistency of FPD pontic fabrication compared to traditional manual techniques. Digital methods produce thinner pontics with superior anatomical accuracy, although vertical gap measurements are similar across methods. These findings emphasize the benefits of CAD-CAM in enhancing prosthetic outcomes and suggest potential improvements in clinical practices for prosthodontic rehabilitation.

CAD-CAM pressure-exerting device to create an ovate pontic for an implant-supported fixed partial denture

[Application of Computer Aided Design-Computer Aided Manufacture Technique in Mandible Defect Reconstruction with Individual Titanium Prosthesis].

[Application of Computer Aided Design/computer Aided Manufactured Techniques in Mandible Defect Reconstruction].

Enhancing Fixed Partial Denture Pontic Fabrication: An In Vitro Comparative Study of the Digital and Manual Techniques

Computer Aided Design and Computer Aided Manufacture of Sacrificial Pattern of Removable Partial Denture Framework

Design of Complete Dentures by Adopting CAD Developed for Fixed Prostheses

A Novel Computer-Aided Design/Computer-Assisted Manufacture Method for One-Piece Removable Partial Denture and Evaluation of Fit.

The Role of Digital Facebow for CAD/CAM Implant-Supported Crowns Workflow

[Research and Development of Computer Aided Design and Rapid Prototyping Technology for Complete Denture].

A custom CAD-CAM resilient attachment: A dental technique

A Technique to Fabricate a Custom CAD-CAM Periapical Radiographic Film Holder for Implant Assessment.

Digital Technologies for Restorative Dentistry

A Digital Technique for Replicating Peri-Implant Soft Tissue Contours and the Emergence Profile

[Computer-Aided Design for Occlusal Rest of the Removable Partial Denture].

Combining Intraoral and Face Scans for the Design and Fabrication of Computer-Assisted Design/Computer-Assisted Manufacturing (CAD/CAM) Polyether-Ether-Ketone (PEEK) Implant-Supported Bars for Maxillary Overdentures

Computer-assisted prosthetic planning and implant design with integrated digital bite registration: a treatment protocol

A fully digital workflow to design anterior guidance for an implant-supported single crown using a modified patient-specific motion technique

New layer-based imaging and rapid prototyping techniques for computer-aided design and manufacture of custom dental restoration

A full digital workflow to prefabricate an implant-supported interim restoration: case report and a novel technique

A Digital Technique for Fabricating Implant-Supported Interim Restorations in the Esthetic Zone.

Case report: Fabrication of a dental implant guide based on tetrahedron positioning technology