Abstract:Abstract In deep underground mining, achieving stable support for roadways along with long service life is critical and the complex geological environment at such depths frequently presents a major challenge. Owing to the coupling action of multiple factors such as deep high stress, adjacent faults, cross-layer design, weak lithology, broken surrounding rock, variable cross-sections, wide sections up to 9.9 m, and clusters of nearby chambers, there was severe deformation and breakdown in the No. 10 intersection of the roadway of large-scale variable cross-section at the − 760 m level in the Nanfeng working area of the Wuyang Coal Mine. As there are insufficient examples in engineering methods pertaining to the geological environment described above, the numerical calculation model was oversimplified and support theory underdeveloped; therefore, it is imperative to develop an effective support system for the stability and sustenance of deep roadways. In this study, a quantitative analysis of the geological environment of the roadway through field observations, borehole peeking, and ground stress testing is carried out to establish the FLAC 3D variable cross-section crossing roadway model. This model is combined with the strain softening constitutive (surrounding rock) and Mohr-Coulomb constitutive (other deep rock formations) models to construct a compression arch mechanical model for deep soft rock, based on the quadratic parabolic Mohr criterion. An integrated control technology of bolting and grouting that is mainly composed of a high-strength hollow grouting cable bolt equipped with modified cement grouting materials and a high-elongation cable bolt is developed by analyzing the strengthening properties of the surrounding rock before and after bolting, based on the Heok-Brown criterion. As a result of on-site practice, the following conclusions are drawn: (1) The plastic zone of the roof of the cross roadway is approximately 6 m deep in this environment, the tectonic stress is nearly 30 MPa, and the surrounding rock is severely fractured. (2) The deformation of the roadway progressively increases from small to large cross-sections, almost doubling at the largest cross-section. The plastic zone is concentrated at the top plate and shoulder and decreases progressively from the two sides to the bottom corner. The range of stress concentration at the sides of the intersection roadway close to the passageway is wider and higher. (3) The 7 m-thick reinforced compression arch constructed under the strengthening support scheme has a bearing capacity enhanced by 1.8 to 2.3 times and increase in thickness of the bearing structure by 1.76 times as compared to the original scheme. (4) The increase in the mechanical parameters c and φ of the surrounding rock after anchoring causes a significant increase in σ c and σ t ; the pulling force of the cable bolt beneath the new grouting material is more than twice that of ordinary cement grout, and according to the test, the supporting stress field shows that the 7.24 m surrounding rock is compacted and strengthened in addition to providing a strong foundation for the bolt (cable). On-site monitoring shows that the 60-day convergence is less than 30 mm, indicating that the stability control of the roadway is successful.

Study on deformation mechanism and control technology of surrounding rock during reuse of gob side entry retaining by roof pre-splitting

Study on the Bolt-mesh-anchor Surrounding Mechanism of a Roadway in a Soft and Thick Rock Seam

Study Of Surrounding Rock Damage Induced By Tunnel Boring Machine Driving Tunnel At West Route Of South To North Water Transfer Project

Deformation and Failure Evolution Law and Support Optimization of Gob-Side Entry in Weakly Cemented Soft Rock under the Influence of Fault

Deformation mechanism and control technology of gob-side entry retaining with roadside backfilling: a numerical analysis and field investigation

Study on Safety Control of Large-Section Roadway with High Stress and Broken Surrounding Rock

Study on Deformation Failure Mechanism and Control Technology of Surrounding Rock in Soft Rock Roadway

Asymmetric Damage Mechanisms and Prevention Technology in Large-Section Gob-Side Entry Retaining

Instability Mechanism and Surrounding Rock Control Technology of Roadway Subjected to Mining Dynamic Loading with Short Distance: A Case Study of the Gubei Coal Mine in China

Study on Mechanical Properties and Control Technology of Surrounding Rock in the Fracture Zone of a Roadway

Study on Surrounding Rock Deformation Mechanism and Control of Roadway with Large Section and Extra-Thick Top Coal

Deformation Mechanism and Support Technology of Deep and High-Stress Soft Rock Roadway

Stability analysis of integral load-bearing structure of surrounding rock of gob-side entry retention with flexible concrete formwork

Study on Stability Control of Gob-Side Entry Retaining Structure Without Filling Wall in Hard Roof

Reused roadway failure mechanism and control strategies: a case study of the Shuangliu Coal Mine, China

Surrounding Rocks Deformation Mechanism and Roof Cutting-Grouting Joint Control Technology for Soft and Thick Coal Seam Roadway

Surrounding Rock Stability Control Technology of Roadway in Large Inclination Seam with Weak Structural Plane in Roof

Study on Failure Mechanism and Control Technology of Roadway Surrounding Rock under Complex Occurrence Coal Seam

Study on instability mechanism of soft rock roadway and pressure-relief bolt-grouting support technology

Study on Mechanical Mechanism and Stability of Surrounding Rock in Fault Structure Roadway

Failure Analysis of Intersections of Large-Scale Variable Cross-Section Roadways in Deep Soft Rock and Study of Integrated Control Technology of Bolting and Grouting