Abstract:The cryogenic propulsion era started with the use of liquid rockets. These rocket engines use propellants in liquid form with reasonably high density, allowing reduced tank size with a high mass ratio. Cryogenic engines are designed for liquid fuels that have to be held in liquid form at cryogenic temperature and gas at normal temperatures. Since propellants are stored at their boiling temperature or subcooled condition, minimal heat infiltration itself causes thermal stratification and self-pressurization. Due to stratification, the state of propellant inside the tank varies, and it is essential to keep the propellant properties in a predefined state for restarting the cryogenic engine after the coast phase. The propellant’s condition at the inlet of the propellant feed system or turbo pump must fall within a narrow range. If the inlet temperature is above the cavitation value, cavitation will likely to happen to result in the probable destruction of the flight vehicle. The present work aims to find an effective method to reduce the stratification phenomenon in a cryogenic storage tank. From previous studies, it is observed that the shape of the inner wall surface of the storage tank plays an essential role in the development of the stratified layer. A CFD model is established to predict the rate of self-pressurization in a liquid hydrogen container. The Volume of Fluid (VOF) method is used to predict the liquid–vapor interface movement, and the Lee phase change model is adopted for evaporation and condensation calculations. A detailed study has been conducted on a cylindrical storage tank with an iso grid and rib structure. The development of the stratified layer in the presence of iso grid and ribs are entirely different. The buoyancy-driven free convection flow over iso grid structure result in velocity and temperature profile that differs significantly from a smooth wall case. The thermal boundary layer was always more significant for iso grid type obstruction, and these obstructions induces streamline deflection and recirculation zones, which enhances heat transfer to bulk liquid. A larger self-pressurization rate is observed for tanks with an iso grid structure. The presence of ribs results in the reduction of upward buoyancy flow near the tank surface, whereas streamline deflection and recirculation zones were also perceptible. As the number of ribs increases, it nullifies the effect of the formation of recirculation zones. Finally, a maximum reduction of 32.89% in the self-pressurization rate is achieved with the incorporation of the rib structure in the tank wall.

Effect of baffles on pressurization and thermal stratification in a LN2 tank under micro-gravity

Experimental study of self-pressurizing transfer system for cryogenic liquid

Experimental and Numerical Investigation of Stratification and Self pressurization in a High Pressure Liquid Nitrogen Storage Tank

Thermal stratification and self-pressurization in a cryogenic propellant storage tank considering capillary effect in low-gravity

Numerical Simulation on Interface Evolution and Pressurization Behaviors in Cryogenic Propellant Tank on Orbit

Numerical study on thermodynamic characteristics of large-scale liquid hydrogen tank with baffles under sloshing conditions

Simulation of Single Bubble Dynamic Process in Pool Boiling Process under Microgravity Based on Phase Field Method

Analysis and Modeling of No-Vent Filling Process for Liquid-Hydrogen Tank in Orbital Conditions

Numerical Study of the Filling Process of a Liquid Hydrogen Storage Tank under Different Sloshing Conditions

Liquid sloshing behaviours in an elastic tank and suppression effect of baffles

LIQUID NITROGEN (OXYGEN SIMULANT) TEST DATA ANALYSIS THERMODYNAMIC VENT SYSTEM

Dynamic Thermal Performance of Cryogenic Liquid Hydrogen Heating from Gas-Liquid Stratification to Supercritical under a Constant Heat Flux Condition: A Two-Step Simulation

Parametric optimization and analysis of thermodynamic venting system in liquid hydrogen tank under microgravity

Effect of Roughness Elements on the Evolution of Thermal Stratification in a Cryogenic Propellant Tank

Modeling and Simulation of Cryogenic Propellant Tank Pressurization in Normal Gravity

Numerical Simulation on Partially Liquid-Filled Sloshing with Baffle Under Different Density Ratios by the CLSVOF/IB Method

Experimental study on sloshing reduction effects of vertical baffles with different perforation shapes in a rectangular tank

Experimental investigation of liquid transport in a vane type tank of satellite with microgravity

Sloshing reduction in microgravity with passive baffles: Design, performance, and supplemental thermocapillary control

Influence of Structured Packing Geometric Parameters on Flow and Mass Transfer Performance of Liquid Nitrogen and Oxygen for Cryogenic Distillation

Testing and comparison of a thermodynamic vent system operating in different modes in a liquid nitrogen tank