Abstract:Introduction Cadmium usually exists in nature as a compound and under normal environmental conditions, its small content will not affect human health. Nevertheless, with human society's development, heavy metal ions pollution has become substantially serious, and they have serious biological toxicity. Hence, it is important to develop simple, rapid, sensitive, and portable devices for Cd 2+ sensing [1]. In the present work, we show how paper based microfluidic sensors improve sensitivity and limit of detection (LOD) in comparison to classical screen-printed carbon-based electrode (SPCE). Furthermore, the presented microfluidic electrochemical carbon-based sensor (μCS) do not employ critical metals and rely on graphite foil that is modified by N-doped carbon nanoonions (N-CNOs) N-CNOs. Experimental For the synthesis of N-doped CNOs the Kuznetsov method was employed [2]. The alignment of the component for μCS device is sketched below. After providing the analyte solution through the sponge the electrochemical detection is carried out through accumulation of the metal at the working electrode for varying times and cathodic potentials. The final detection is carried out through square wave anodic stripping voltammetry (SWASV) of the accumulated metal. Results and discussion To realize a sensitive measurement, some experimental conditions including the optimal amount of the employed N-doped CNOs and Nafion in the nanocomposite, deposition time and potential, and the effect of pH of supporting electrolyte were studied. By increasing the deposition time ranging from 0 to 5 min, the SPCE/N-CNOs signal was increased and after that, it remains roughly constant because the WE surface is being saturated and also the amount of analyte in the droplet was reduced due to the presence of a stagnant flow. However, for μCS/N-CNOs by increasing the accumulation time ranging from 0 to 10 min the signal was increased which shows that the electrode surface is still far from being saturated (because of the live flow). A linear concentration range from 1.0 to 100.0 μg L - 1 was achieved using SWASV. Also, the LOD and sensitivity are calculated to be 0.5 μg L - 1 and 1.02 μA μM -1 cm -2 , respectively. Additionally, the method was successfully employed for measurements of Cd 2+ in different real samples, which demonstrated the excellent applicability of the device for the adsorption and detection of heavy metal ions. Conclusion The μCS/N-CNOs offers several core advantages over SPCE/N-CNOs in terms of cost, simplicity, analysis time, and sensitivity. These unique advantages are due to the combined microfluidic configuration, 3D electrode layout, and a unique modifier. We believe our findings would have significant implications in developing other portable, fast, and cost-effective electrochemical detection platforms, such as clinical diagnosis and security inspection. References [1]. Fan, Guojing, Dasun Zhai, and Dongsheng Zou. "Highly sensitive electrochemical determination of cadmium (II) in environmental water based on the electrodeposited bismuth nanoparticles." Int. J. Electrochem. Sci 11 (2016): 4362-4370. [2]. Krishnamurthy, S., et al. "In situ formation of onion-like carbon from the evaporation of ultra-dispersed nanodiamonds." Carbon 52 (2013): 145-149. Figure 1

Eco-friendly synthesis of nanoceria using orange peel extract for electrochemical detection of selective cadmium ions

Efficient sensor based on CeCo3O6 nanocomposite for the electrochemical detection of cadmium and copper ions

Morphology-controlled electrochemical sensing of environmental Cd2+ and Pb2+ ions on expanded graphite supported CeO2 nanomaterials

Increasing Sensitivity and Selectivity for Heavy Metal Sensing through Microfluidic Electrochemical Sensor

A novel electrochemical sensor modified with carbon nanocomposites and ion‐imprinted polymers and its high selectivity for cadmium ion detection in real samples

Development of a robust method for Cd(II) ions analysis using CeO2- and CeO2-Cu-BTC-based electrochemical sensors

Application of Nitrogen-Doped Reduced Graphene Oxide-Persimmon Tannin Nanocomposites for Electrochemical Detection of Cd (II) in Water Resources

A Highly Sensitive Electrochemical Sensor for Cd2+ Detection Based on Prussian Blue-PEDOT-Loaded Laser-Scribed Graphene-Modified Glassy Carbon Electrode

Nitrogen and Sulfur Co-doped Carbon Dots as a Turn-Off Fluorescence Probe for the Detection of Cerium and Iron

Flexible carbon fiber cloth supports decorated with cerium metal- organic frameworks and multi-walled carbon nanotubes for simultaneous on-site detection of Cd2+ and Pb2+ in food and water samples

WO3-Nanocrystal-Modified Electrodes for Ultra-Sensitive and Selective Detection of Cadmium (Cd2+) Ions

Electrochemical sensor based on cerium niobium oxide nanoparticles modified electrode for sensing of environmental toxicity in water samples

An Electrochemical Sensor for the Determination of Trace Concentrations of Cadmium, Based on Spherical Glassy Carbon and Nanotubes

Construction of electrochemical sensing interface towards Cd(II) based on activated g-C3N4 nanosheets: considering the effects of exfoliation and protonation treatment

Graphene oxide-based sorbents modified with waste orange peel biochar for Cd(II) removal from aqueous waste streams

Facile one step green synthesis of CdO-CdS hybrid nanocomposite: Its electrochemical and photoluminescence applications

Ca-MOF-Polymer Modified Thin-Film Electrode for Detection of Toxic Cadmium (Cd2+) in Biofluid and Environmental Fluid

ZnO Doped Silica Nanoparticles (ZnO@SiO2) for Enhanced Electrochemical Detection of Cd2+ Ions in Real Samples

Cerium vanadate/functionalized carbon nanofiber composite for the electrochemical detection of nitrite

Enhancing Heavy Metal Detection through Electrochemical Polishing of Carbon Electrodes

Chitosan-assisted self-assembly of flower-shaped ε-Fe2O3 nanoparticles on screen-printed carbon electrode for Impedimetric detection of Cd2+, Pb2+, and Hg2+ heavy metal ions in various water samples