Abstract:A cross‐linked glycidyl methacrylate‐acrylonitrile network is constructed through poly(vinylidenefluoride‐co‐hexafluoropropylene) matrix by adopting free radical polymerization and ring‐opening polymerization. The structure of poly(glycidyl methacrylate and acrylonitrile)@poly‐(vinylidene fluoride‐hexafluoropropylene) can be visualized by polarization microscopy. Enabled by the introduction of successive Li ion transfer paths and the dual in‐situ polymerization strategy, excellent electrochemical performances are achieved. Poly(vinylidenefluoride‐co‐hexafluoropropylene) (PVDF‐HFP) is one of the most promising candidate electrolyte matrices for high energy batteries. However, the spherical skeleton structure obtained through the conventional method fails to build continuous Li ion transmission channels due to the slow volatilization of high boiling solvent, leading to inferior cycling performance, especially in a Ni‐rich system. Herein, a novel strategy is presented to enrich the Li ion transfer paths and improve the Li ion migration kinetics. The tactic is to prepare cross‐linked segments through the PVDF‐HFP matrix by adopting free radical polymerization and Li salt induced ring‐opening polymerization. Most significantly, the visualization of the structure of as‐prepared electrolyte is innovatively realized with the combination of polarization microscopy, transmission electron microscopy, scanning electron microscope‐energy dispersive spectroscopy, PVDF‐HFP, and cross‐linked network form interconnected microstructures. Therefore, poly(glycidyl methacrylate and acrylonitrile)@poly(vinylidene fluoride‐hexafluoropropylene) electrolyte presents a high ionic conductivity (1.04 mS cm−1 at 30 °C) and a stable voltage profile for a Li/Li cell after 1200 h. After assembly with a LiNi0.8Co0.15Al0.05O2 cathode, a high discharge specific capacity of 190.3 mAh g−1 is delivered, and the capacity retention reaches 88.2% after 100 cycles. This work provides a promising method for designing high‐performance polymer electrolytes for lithium metal batteries.

Lithium Salt‐Induced In Situ Polymerizations Enable Double Network Polymer Electrolytes

Lithium Salt-Induced in Situ Living Radical Polymerizations Enable Polymer Electrolytes for Lithium-Ion Batteries

In Situ Construction of Polymer Electrolytes with Dynamic Covalent Networks via Initiator-Free Thiol-Methacrylate Radical Polymerization

Facile Assembly of C–N Bond-Containing Polymer Electrolytes Enabled by Lithium Salt-Catalyzed Aza-Michael Addition

Dual In Situ Polymerization Strategy Endowing Rapid Ion Transfer Capability of Polymer Electrolyte toward Ni‐Rich‐Based Lithium Metal Batteries

Click chemistry-initiated highly uniform semi-interpenetrating polymer electrolyte with dual salts for high-performance lithium metal batteries

In-situ construction of PDOL electrolyte with dual-reinforced stable interface for high-voltage lithium metal batteries

Facile Fabrication of Polymer Electrolytes via Lithium Salt-Accelerated Thiol-Michael Addition for Lithium-Ion Batteries

In Situ Polymerization Design of a Quasi-Solid Electrolyte Enhanced by NMP Additive for Lithium Metal Batteries

An initiator-free and solvent-free in-situ self-catalyzed crosslinked polymer electrolyte for all-solid-state lithium-metal batteries

Facile Fabrication of Polymer Electrolytes with Branched Structure Via Deep Eutectic Electrolyte-Enabled in Situ Polymerizations.

In Situ Constructing Ultrathin, Robust‐Flexible Polymeric Electrolytes with Rapid Interfacial Ion Transport in Lithium Metal Batteries

Fabrication of Polymer Electrolyte Via Lithium Salt-Induced Surface-Initiated Radical Polymerization for Lithium Metal Batteries

A Rational Design of Solid Polymer Electrolyte with High Salt Concentration for Lithium Battery

Poly(ester‐alt‐acetal) Electrolyte via In Situ Copolymerization for High‐Voltage Lithium Metal Batteries: Lithium Salt Catalysts Deciding Stable Solid‐Electrolyte Interphase

Boosting the Performances of Lithium Metal Batteries Through In-Situ Construction of Dual-Network Self-Healing Gel Polymer Electrolytes

A Dual-Salt Peo-Based Polymer Electrolyte with Cross-Linked Polymer Network for High-Voltage Lithium Metal Batteries

A Quasi‐Double‐Layer Solid Electrolyte with Adjustable Interphases Enabling High‐Voltage Solid‐State Batteries

Self-Healing Single-Ion Conducting Polymer Electrolyte Formed Via Supramolecular Networks for Lithium Metal Batteries

Eutectic-Based Polymer Electrolyte with the Enhanced Lithium Salt Dissociation for High-Performance Lithium Metal Batteries

Double‐Network Ionogel Electrolyte with Superior Mechanical Performance and High Safety for Flexible Lithium‐Ion Batteries