Abstract:Organic Lewis bases [2,2'-bipyridine (BPY), 4-hydroxy-1,5-naphthyridine-3-carbonitrile (DQCN), and thenoyltrifluoroacetone (TTFA)] with bi-coordination sites of N and O were employed as perovskite surface defect passivants to address the efficiency and stability issues of perovskite solar cells (PSCs), with typical phenethylammonium iodide (PEAI) and piperazinium iodide (PI) passivants as reference. The surface properties of the perovskite films before and after passivation were characterized by Fourier-transform infrared, ultraviolet-visible, photoluminescence (PL), and time-resolved PL spectroscopy, X-ray diffraction, ultraviolet photoelectron spectroscopy, scanning electron microscopy, and atomic force microscopy. The characterizations reveal that BPY, DQCN, or TTFA forms coordination bonds with exposed "Pb2+", leading to a slight decrease in the highest occupied molecular orbital or lowest unoccupied molecular orbital energy level and bandgap. These passivants (especially TTFA) can passivate the perovskite surface defects to inhibit non-radiative recombination while having almost no influence on the grain size and surface morphology. Utilizing the passivated perovskite as the light absorption layer, solar cells with an inverted configuration of indium tin oxide/NiO x /passivated MAPbCl x I3-x /C60/BCP/Ag have been fabricated, and power conversion efficiencies of 19.22, 17.85, 16.49, 16.31, and 17.88% have been achieved from PEAI, PI, BPY, DQCN, and TTFA, respectively. All the device performance based on passivated perovskite is superior to that of the control (15.75%) owing to the reduced carrier recombination. The device from TTFA exhibits almost comparable efficiency to that of PEAI and PI controls, indicating that TTFA has an equal excellent passivation effect to state-of-the-art PEAI and PI. Furthermore, the devices based on BPY, DQCN, and TTFA show superior long-term stability with an efficiency loss of only 13.2, 16.7, and 12.9%, respectively, after being stored for 40 days in a ∼12% humidity, low-oxygen level environment, which is 45.4, 38.8, and 44.4% for the control, PEAI, and PI devices, respectively, primarily due to the improved hydrophobicity of the perovskite surface. Our results demonstrate that it is feasible to achieve high-efficiency and long-term-stable perovskite solar cells via selecting the appropriate molecules to passivate perovskite surface defects.

Multifunctional interface passivation by benzothiophene amine for stable perovskite solar cells with suppressed charge recombination

Synergistic Effects of the Physical Modification and Chemical Passivation Enabling Efficient Perovskite Solar Cells

Enhancing Performance and Stability of Perovskite Solar Cells through Surface Defect Passivation with Organic Bidentate Lewis Bases

Interfacial defect passivation by multiple-effect molecule for efficient and stable perovskite solar cells

Introduction of Multifunctional Triphenylamino Derivatives at the Perovskite/HTL Interface To Promote Efficiency and Stability of Perovskite Solar Cells

Perovskite Passivation with a Bifunctional Molecule 1,2‐Benzisothiazolin‐3‐One for Efficient and Stable Planar Solar Cells

SnO2-Perovskite Interface Engineering Based on Bifacial Passivation Via Multifunctional N-(2-Acetamido)-2-aminoethanesulfonic Acid Toward Efficient and Stable Solar Cells

Multifunctional Small Molecule as Buried Interface Passivator for Efficient Planar Perovskite Solar Cells

Multifunctional Thiophene-Based Interfacial Passivating Layer for High-Performance Perovskite Solar Cells

Perovskite Surface Passivation Using Thiophene-Based Small Molecules for Efficient and Stable Solar Cells

Interfacial Energy Level Alignment and Defect Passivation by Using a Multifunctional Molecular for Efficient and Stable Perovskite Solar Cells

Interfacial Defect Passivation and Charge Carrier Management for Efficient Perovskite Solar Cells via a Highly Crystalline Small Molecule

Enhanced Perovskite Solar Cell Stability and Efficiency via Multi‐Functional Quaternary Ammonium Bromide Passivation

Full-scale chemical and field-effect passivation: 21.52% efficiency of stable MAPbI3 solar cells via benzenamine modification

Defect passivation and interface modification by tetra-n-octadecyl ammonium bromide for efficient and stable inverted perovskite solar cells

Enhanced charge carrier transport and defects mitigation of passivation layer for efficient perovskite solar cells

Tailoring the Interface by a Multifunctional Amphiphilic Molecule Enabled 24.84%-Efficiency and Stable Perovskite Solar Cells

Improving the Performance and Stability of Perovskite Solar Cells through Buried Interface Passivation Using Potassium Hydroxide

Intermolecular π–π Conjugation Self‐Assembly to Stabilize Surface Passivation of Highly Efficient Perovskite Solar Cells

Reconfiguration toward Self‐Assembled Monolayer Passivation for High‐Performance Perovskite Solar Cells

Efficient and Stable Chemical Passivation on Perovskite Surface Via Bidentate Anchoring