Abstract:Proceedings of the Institution of Mechanical Engineers, Part H: Journal of Engineering in Medicine, Ahead of Print. In recent years, the triply periodic minimal surface (TPMS)-based scaffolds have been served as one of the crucial types of structures for biological replacements, the energy absorber, etc. Meanwhile, the development of additive manufacturing (AM) has facilitated the production of TPMS scaffolds with complex microstructures. However, the design maps of TPMS scaffolds, especially considering the AM constraints, remain unclear, which has hindered the design and application of TPMS scaffolds. The aims of the present study were to develop an efficient computational modeling framework for investigating the design maps of TPMS scaffolds simultaneously considering the AM constraints, the biological requirements, and the structural anisotropy. To demonstrate the computational framework, five widely-used topologies of the TPMS-based scaffolds (i.e. the Diamond, the Gyroid, the Fischer-Koch S, the F-RD, and the Schwarz P) were used, whose design maps for the surface-to-volume ratio and the effective elastic modulus were also investigated. The results showed that as the porosities increase, the design ranges of the surface-to-volume ratios decreases for all the structures. Compared with the effect of the constraint for the pore size, the minimal structural thickness for AM constraint has a greater effect on the surface-to-volume ratio. Regarding the elastic modulus, in the region of low porosity (approximately 0.5–0.7), the range for the effective elastic modulus of Schwarz P is the widest (approximately 2.24–32.6 GPa), but the Gyroid can achieve both high porosity and low effective elastic modulus (e.g. 0.61 GPa at the porosity of 0.90). These results and the method developed in the present study provided important basis and guidance for the design and application of the TPMS-based porous structures.

Comparative evaluation of printability and compression properties of poly-ether-ether-ketone triply periodic minimal surface scaffolds fabricated by laser powder bed fusion

Surface porous poly-ether-ether-ketone based on three-dimensional printing for load-bearing orthopedic implant

Mechanical Properties of 3D-Printed Porous Poly-ether-ether-ketone (PEEK) Orthopedic Scaffolds

Manufacturability, Mechanical Properties, Mass-Transport Properties and Biocompatibility of Triply Periodic Minimal Surface (TPMS) Porous Scaffolds Fabricated by Selective Laser Melting

Additively-manufactured PEEK/HA porous scaffolds with highly-controllable mechanical properties and excellent biocompatibility

Fused Deposition Modeling of Poly(ether Ether Ketone) Scaffolds

3D-Printed Porous Polyether-Ether-Ketone Composite Scaffolds for Better Osteogenic Activity

Osteointegration of 3D-Printed Fully Porous Polyetheretherketone Scaffolds with Different Pore Sizes

Influence of structural parameters of 3D-printed triply periodic minimal surface gyroid porous scaffolds on compression performance, cell response, and bone regeneration

Optimizing process parameters of fused deposition molding for 3D printing customized control of polyetheretherketone scaffolds

Laser Powder Bed Fusion-built Ti6Al4V Bone Scaffolds Composed of Sheet and Strut-based Porous Structures: Morphology, Mechanical Properties, and Biocompatibility

Full compression response of FG-based scaffolds with varying porosity via an effective numerical scheme

On the mechanical aspect of additive manufactured polyether-ether-ketone scaffold for repair of large bone defects

Additively-manufactured Poly-Ether-ether-ketone (PEEK) Lattice Scaffolds with Uniform Microporous Architectures for Enhanced Cellular Response and Soft Tissue Adhesion

Mechanical properties and failure analysis of 3D-printing micron-scale ceramic-based triply periodic minimal surface scaffolds under quasi-static-compression and low-speed impact loads

Comparison of the design maps of TPMS based bone scaffolds using a computational modeling framework simultaneously considering various conditions

Mechanical Properties and Microstructure Characteristics of Lattice-Surfaced PEEK Cage Fabricated by High-Temperature Laser Powder Bed Fusion

Fabrication and properties of interweaved poly(ether ether ketone) composite scaffolds

Integrated porous polyetheretherketone/hydroxyapatite scaffolds: design, manufacturing and performance evaluation

Design, Fabrication, and Characterization of 3D-Printed Multiphase Scaffolds Based on Triply Periodic Minimal Surfaces

Tuning Structure in 3D-Printed Scaffolds of Polylactide by Extensional Stress and Its Influence on Properties