Abstract:Tribological properties of engineering components are a key issue due to their effect on the operational performance factors such as wear, surface characteristics, service life and in situ behavior. Thus, for better component quality, process parameters have major importance, especially for metal matrix composites (MMCs), which are a special class of materials used in a wide range of engineering applications including but not limited to structural, automotive and aeronautics. This paper deals with the tribological behavior of Cu-B-CrC composites (Cu-main matrix, B-CrC-reinforcement by 0, 2.5, 5 and 7.5 wt.%). The tribological characteristics investigated in this study are the coefficient of friction, wear rate and weight loss. For this purpose, four levels of sliding distance (1000, 1500, 2000 and 2500 m) and four levels of applied load (10, 15, 20 and 25 N) were used. In addition, two levels of sliding velocity (1 and 1.5 m/s), two levels of sintering time (1 and 2 h) and two sintering temperatures (1000 and 1050 °C) were used. Taguchi’s L16 orthogonal array was used to statistically analyze the aforementioned input parameters and to determine their best levels which give the desired values for the analyzed tribological characteristics. The results were analyzed by statistical analysis, optimization and 3D surface plots. Accordingly, it was determined that the most effective factor for wear rate, weight loss and friction coefficients is the contribution rate. According to signal-to-noise ratios, optimum solutions can be sorted as: the highest levels of parameters except for applied load and reinforcement ratio (2500 m, 10 N, 1.5 m/s, 2 h, 1050 °C and 0 wt.%) for wear rate, certain levels of all parameters (1000 m, 10 N, 1.5 m/s, 2 h, 1050 °C and 2.5 wt.%) for weight loss and 1000 m, 15 N, 1 m/s, 1 h, 1000 °C and 0 wt.% for the coefficient of friction. The comprehensive analysis of findings has practical significance and provides valuable information for a composite material from the production phase to the actual working conditions.

Response Surface Optimization Design of G20CrMo Composite Surface Cylinder Texture Parameters and Analysis of Tribological Performance

Tribological Aspects, Optimization and Analysis of Cu-B-CrC Composites Fabricated by Powder Metallurgy

Simulation and Experimental Study on Tribological Properties of Herringbone Texture on 42CrMo Bearing Alloy Steel Surface

Optimization of Tribological Characteristics of a Combined Pattern Textured Surface Using Taguchi Design

Optimal design of surface texture in meso scale air journal bearing

Analysis of Influencing Factors on the Tribological Behavior of 42CrMo4/17NiCrMo6-4 under Grease Lubrication

Surface texture and heat treatment on the friction performance of cam tappet experimental and fluid-solid coupling numerical study

Influence of Variable-Depth Groove Texture on the Friction and Wear Performance of GCr15–SiC Friction Pairs Under Water Lubrication

Study on the Friction-Reducing Mechanisms of Surface Texture Cemented Carbide under Dry Sliding

A Design of Partial Textured Surface on Gear Washers for Reducing Friction and Wear under Low Speed and Heavy Load Conditions

Optimization of Bionic Texture Parameters by Box–Behnken Method and Study on Tribological Performance of 42CrMo Self-Lubricating Composites in Solid–Liquid Composite Lubrication System

Contact and Tribological Study of Micro/Nano Groove Texture on the Surface of Gas Bearing Materials Based on Nanoscale

Optimization of Groove Texture Profile to Improve Hydrodynamic Lubrication Performance: Theory and Experiments

Influence of concave-convex composite texture on the tribology and transmission performance of wet clutch couples

Tribological Investigation of Composite MoS2-TiO2-ZrO2 Coating Material by Response Surface Methodology Approach

Analysis and Evaluation of the Synergistic Effect of Ceramic Materials and Surface Texture on Anti-Abrasive Particle Wear under Rolling Conditions

Tribological investigations on piston alloy based hybrid nano composite and GGG40 spheroidal cast iron under reciprocating dry sliding conditions

Optimization of Tribological Behaviour of Ti6Al4V/TiB2/TiC Hybrid MMCs Using Response Surface Methodology

Coordinating influence of multilayer graphene and spherical SnAgCu for improving tribological properties of a 20CrMnTi material

Topology optimization of AISI 4140 steel with surface texture filled by multi-solid lubricants for enhancing tribological properties

Friction and wear properties of textured surface for bearing steel with mango-shaped micro geometries