Plant Fiber Reinforcements as Alternatives in Pultruded FRP Composites Manufacturing: A Review

Thinesh Sharma Balakrishnan,Mohamed Thariq Hameed Sultan,Farah Syazwani Shahar,Suhas Yeshwant Nayak,Ain Umaira Md Shah,Tamer Ali Sebaey,Adi Azriff Basri

DOI: https://doi.org/10.1080/15440478.2023.2298396

2024-01-19

Journal of Natural Fibers

Abstract:Recent developments of green technology promote the rising attraction toward developing high-performance and environmentally friendly pultruded products from naturally derived resources. Some factors that attract attention to developing pultruded biocomposites are their lightweight properties, recyclability, and economical and environmentally superior alternatives to synthetic fibers in commercial applications. Researchers have studied that the environmental crisis caused by conventional synthetic materials can be reduced significantly by using sustainable materials instead. This paper aims to review the potential of plant fibers to be used in pultruded composite manufacturing to reduce and replace the use of synthetic materials in pultruded structures. It was found that kenaf and jute fibers have been extensively studied in pultruded plant fiber reinforced composites and pultruded glass/plant fiber reinforced hybrid composites for their mechanical and physical properties under various test parameters. Overall, pultruded PFCs have recorded good mechanical properties but have limitations in water absorption properties for outdoor applications. An overview of the optimum process parameters, limitations, and potential applications of pultruded PFCs are also outlined. Finally, this review summarizes the future scopes and expectations, providing researchers and industrialists with a vision for deeper investigation in developing pultruded PFCs. 绿色技术的最新发展促使人们越来越倾向于利用自然资源开发高性能、环保的拉挤产品. 开发拉挤生物复合材料引起关注的一些因素是其轻质性能、可回收性以及在商业应用中合成纤维的经济和环保替代品. 研究人员研究表明,使用可持续材料可以显著减少传统合成材料造成的环境危机. 本文旨在综述植物纤维在拉挤复合材料制造中的潜力,以减少和取代拉挤结构中合成材料的使用. 研究发现,红麻和黄麻纤维在各种试验参数下的力学和物理性能已在拉挤植物纤维增强复合材料和拉挤玻璃/植物纤维增强混杂复合材料中得到广泛研究. 总体而言,拉挤PFCs具有良好的机械性能,但在户外应用的吸水性能方面存在局限性. 还概述了拉挤PFCs的最佳工艺参数、限制和潜在应用. 最后,这篇综述总结了未来的范围和期望,为研究人员和实业家提供了在开发拉挤全氟氯化碳方面进行更深入研究的愿景.

materials science, textiles

What problem does this paper attempt to address?

The paper primarily discusses how to use plant fibers as reinforcement materials to replace traditional synthetic materials, especially in the pultrusion process for manufacturing fiber reinforced plastic (FRP) composites, against the backdrop of environmental protection technology development. Pultrusion is a method used to produce continuous composite materials with uniform cross sections and is commonly used to manufacture structural components such as beams, rods, and pipes.

The paper points out that plant fibers such as jute and hemp, due to their lightweight, recyclability, and cost-effectiveness, have been widely studied for enhancing pultruded composites and have less environmental impact compared to synthetic fibers. However, these plant fiber reinforced composites may face water absorption issues that can affect their performance when used outdoors.

The article provides an overview of the optimal process parameters, constraints, and potential applications of plant fibers in the pultrusion process. It emphasizes the importance of chemical treatment in improving the interface bonding between fibers and matrix, thereby enhancing the mechanical properties of the composites. Additionally, the paper discusses the application research of different plant fibers, such as kenaf, hemp, flax, and sisal, in pultruded composites, as well as their mechanical and physical properties under various test conditions.

In conclusion, the objective of the paper is to summarize the potential of plant fibers in the manufacturing of pultruded FRP composites, providing a basis for reducing and replacing synthetic materials in pultruded structures and promoting the development of sustainable and high-performance materials.