Abstract:Electrospinning is a simple, versatile technique for fabricating fibrous nanomaterials with the desirable features of extremely high porosities and large surface areas. Using emulsion electrospinning, polytetrafluoroethylene/polyethene oxide (PTFE/PEO) membranes were fabricated, followed by a sintering process to obtain pure PTFE fibrous membranes, which were further utilized against a polyamide 6 (PA6) membrane for vertical contact-mode triboelectric nanogenerators (TENGs). Electrostatic force microscopy (EFM) measurements of the sintered electrospun PTFE membranes revealed the presence of both positive and negative surface charges owing to the transfer of positive charge from PEO which was further corroborated by FTIR measurements. To enhance the ensuing triboelectric surface charge, a facile negative charge-injection process was carried out onto the electrospun (ES) PTFE subsequently. The fabricated TENG gave a stabilized peak-to-peak open-circuit voltage (V-oc) of up to similar to 900 V, a short-circuit current density (J(sc)) of similar to 20 mA m(-2), and a corresponding charge density of similar to 149 mu C m(-2), which are similar to 12, 14, and 11 times higher than the corresponding values prior to the ion-injection treatment. This increase in the surface charge density is caused by the inversion of positive surface charges with the simultaneous increase in the negative surface charge on the PTFE surface, which was confirmed by using EFM measurements. The negative charge injection led to an enhanced power output density of similar to 9 W m(-2) with high stability as confirmed from the continuous operation of the ion-injected PTFE/PA6 TENG for 30 000 operation cycles, without any significant reduction in the output. The work thus introduces a relatively simple, cost-effective, and environmentally friendly technique for fabricating fibrous fluoropolymer polymer membranes with high thermal/chemical resistance in TENG field and a direct ion-injection method which is able to dramatically improve the surface negative charge density of the PTFE fibrous membranes.

Creating Ultrahigh and Long‐Persistent Triboelectric Charge Density on Weak Polar Polymer via Quenching Polarization

Achieving Remarkable Charge Density via Self-Polarization of Polar High-k Material in a Charge-Excitation Triboelectric Nanogenerator

Fabrication of triboelectric polymer films via repeated rheological forging for ultrahigh surface charge density

Negative triboelectric polymers with ultrahigh charge density induced by ion implantation

Quantifying Dielectric Material Charge Trapping and De‐Trapping Ability via Ultra‐Fast Charge Self‐Injection Technique

Regulation of deep and shallow hole/electron trap states and charge conducting behaviors of dielectric tribo-materials for maximizing retained charges

High‐Efficiency Charge Injection with Discharge Mitigation Strategy for Triboelectric Dielectric Materials

Superior triboelectric polymer based on solid-state polymer forging

Effectively Inhibiting Charge Injection and Dielectric Loss of High Permittivity Inorganic Materials by Rationally Coating Organic Polymer for Achieving High Output Charge Density

Dynamic Thermostable Cellulosic Triboelectric Materials from Multilevel‐Non‐Covalent Interactions

Design and synthesis triboelectric polymer for high performance triboelectric nanogenerators

Asymmetric permittivity enhanced bilayer polycaprolactone nanofiber with superior inner interfacial polarization and charge retention for high-output and humidity-resistant triboelectric nanogenerators

An Ultrafast Self‐Polarization Effect in Barium Titanate Filled Poly(Vinylidene Fluoride) Composite Film Enabled by Self‐Charge Excitation Triboelectric Nanogenerator

Superior Charge Density of Triboelectric Nanogenerator via Trap Engineering

Emulsion Electrospinning of Polytetrafluoroethylene (PTFE) Nanofibrous Membranes for High-Performance Triboelectric Nanogenerators.

Radical anion transfer during contact electrification and its compensation for charge loss in triboelectric nanogenerator

Remarkably Enhanced Charge Density of Inorganic Material Via Regulating Contact Barrier Difference and Charge Trapping for Triboelectric Nanogenerator

Triboelectric Polymer with High Thermal Charge Stability for Harvesting Energy from 200 °C Flowing Air

Visualization and standardized quantification of surface charge density for triboelectric materials

Chemical structure-based design of triboelectric materials for high-performance TENGs

Effective Interfacial Energy Band Engineering Strategy Toward High-Performance Triboelectric Nanogenerator