Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

Influence of pressure on the structural, elastic, hardness and thermodynamic behavior of Al-rich region TMAl 12 -type (TM=Mo, W and Cr) alloys

The first-principles calculations for the elastic properties of Zr2Al under compression

First-principles Study of Ni-Al Intermetallic Compounds under Various Temperature and Pressure

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

First-principles Study of Mechanical Properties and Electronic Structures of the Nickel-molybdenum Binary Compounds Under Pressure

Theoretical Study of Elastic and Electronic Properties of Al5Mo and Al5W Intermetallics under Pressure

The Mechanical and Thermodynamic Properties of Heusler Compounds Ni2xal (X = Sc, Ti, V) under Pressure and Temperature: A First-Principles Study

GPa level pressure-induced phase transitions and enhanced corrosion resistance of AlCrMoSiTi high-entropy alloys

The Pressure Dependence of Physical Properties of (w2/3ti1/3)3alc2 and Its Counterpart W3AlC2 by First-Principles Calculations

First-principles Investigations on Structural, Elastic, Thermodynamic and Electronic Properties of Ni3X (X = Al, Ga and Ge) under Pressure

Ab-initio Study of Phase Stability, Elastic and Thermodynamic Properties of AlY Alloy under Pressure

Novel High-Pressure Phases of Alp from First Principles

Physical properties and Debye temperature of Al7Cu2Fe alloy under various pressures analyzed by first-principles

Pressure Effects on Elastic and Thermodynamic Properties of Zr3al Intermetallic Compound

Theoretical study of the elastic and thermodynamic properties of Pt$_{3}$Al with the L1$_{2}$ structure under high pressure

Anisotropy in Elasticity and Physical Properties of Ti2B under High Pressure

First-Principles Investigation of Thermodynamic, Elastic and Electronic Properties of Al3v and Al3nb Intermetallics under Pressures

Pressure Effect on Elastic Constants and Related Properties of Ti3Al Intermetallic Compound: A First-Principles Study

Phase Transformations of Al-bearing High-Entropy Alloys AlxCoCrFeNi (x=0, 0.1, 0.3, 0.75, 1.5) at High Pressure

Structural Stability, Elasticity, Thermodynamics, and Electronic Structures of L12-type Ni3X (X = Al, Ti, V, Nb) Phases under External Pressure Condition

Ab initio study of AlCu2M (M = Sc, Ti and Cr) ternary compounds under pressures