Abstract:Reversible and convenient bonding underwater between hydrogel lubrication film and substrate is one of the challenges in the field of tribology. In this study, the lubrication film was combined with the silicone rubber to prepare hydrogel-lubricated silicone rubber with reversible wet adhesion. Polydimethylsiloxane（PDMS） with low degree of crosslink was used as an underwater adhesion material, and the initiator benzophenone was buried on its surface/subsurface, then the hydrogel lubricating film Poly（acrylic acid-co-acrylamide） [P（AA-co-AAm）] was grown on the surface through surface photopolymerization. The interface structure of obtained hydrogel-lubricated silicone rubber was explored by field emission scanning electron microscope（FESEM）. The effects of ratio of hydrogel monomers,concentration of crosslinking agent, and polymerization time on performance of films were explored. The ratio of curing agent in PDMS was adjusted to explore its effects on adhesion and tribological properties of films. The results showed that a densely connected structure formed between the interface of hydrogel and PDMS. As the content of acrylic acid increased, the friction coefficient showed a trend of first decrease and then increase. When the content of acrylamide was further reduced, the acrylic acid segment absorbed water easily and swelled, leading to the reduction of mechanical strength and increase of friction coefficient. When the molar ratio of acrylic acid to acrylamide was 1:1, the hydrogel exhibited excellent tribological properties and mechanical strength. When the content of the crosslinking agent increased, the mechanical properties of hydrogel was optimized, and it exhibited better lubrication property. In addition,the modulus of PDMS increased as the content of curing agent, while the friction coefficient showed the opposite trend.;when the mass ratio of PDMS silane prepolymer to curing agent was 30:1, PDMS had favorable mechanical properties,adhesion performance and low friction coefficient. The prepared hydrogel-lubricated silicone rubber made the hydrogel adhesive underwater and endowed the silicone rubber with excellent lubrication and anti-wear properties. PDMS substrate was worn severely in the sliding direction after the friction test, its surface was damaged and there were obvious pits. In contrast, the hydrogel film only produced very slight scratches. The wear scar of the hydrogel was investigated, and the results showed that after nearly 3 000 cycles, the surface layer of the hydrogel film did not change much, which proved that the hydrogel film had excellent resistance to abrasiveness compared to PDMS. After repeated adhesion tests, the hydrogel film still had excellent adhesion properties. In addition, the hydrogel-lubricated silicone rubber had different adhesion on two sides. PDMS side showed good adhesion to titanium alloy, PTFE, and ceramics underwater while the hydrophilic hydrogel layer had no adhesion to titanium alloys, ceramics, etc. underwater, and directly falls off the surface of the materials.

In situ covalent bonding in polymerization to construct robust hydrogel lubrication coating on surface of silicone elastomer

Constructing a biomimetic robust bi-layered hydrophilic lubrication coating on surface of silicone elastomer

A Universal Strategy for Growing a Tenacious Hydrogel Coating from a Sticky Initiation Layer

Fabrication of robust hydrogel coatings on polydimethylsiloxane substrates using micropillar anchor structures with chemical surface modification.

Robust and Lubricating Interface Semi‐Interpenetrating Network on Inert Polymer Substrates Enabled by Subsurface‐Initiated Polymerization

In-Situ Growth of Hydrogel Lubrication Film on Self-Adhesive Silicon Elastomer Surface and Its Performance

A Bioinspired Hydrogel-Elastomer Hybrid Surface for Enhanced Mechanical Properties and Lubrication

Robust, Sprayable, and Multifunctional Hydrogel Coating Through A Polycation Reinforced (PCR) Surface Bridging Strategy

Successive Redox-Reaction-Triggered Interface Radical Polymerization for Growing Hydrogel Coatings on Diverse Substrates.

Innovating Lubrication with Polyelectrolyte Hydrogels: Sustained Performance Through Lipid Dynamics

Layered Hydrogel with Controllable Surface Dissociation for Durable Lubrication

Tunable cohesion and water lubrication of PEG- g -PMHS- c -PMVS copolymer membranes

Enzyme‐Immobilized Surface‐Catalyzed Cross‐Linking: Creating Multifunctional Double Network Hydrogel Coatings on Diverse Substrates

Transparent PDMS Surfaces with Covalently Attached Lubricants for Enhanced Anti-adhesion Performance

Hydrogen Bonds-Pinned Entanglement Blunting the Interfacial Crack of Hydrogel-Elastomer Hybrids

Tailoring Dynamic Chains of Cross‐Linked PDMS to Hinder Oil Penetration

One-Pot Construction of Articular Cartilage-Like Hydrogel Coating for Durable Aqueous Lubrication

Superspreading of Polyelectrolyte Complex Solution for Constructing Hydrogel Coatings on Diverse Substrates

Bioinspired polymer-incorporating self-lubricating and antifouling hydrogels

Growth of Double-Network Tough Hydrogel Coatings by Surface-Initiated Polymerization

Wide-range Controllable Stick-to-slip Hydrogels by Synergistic Effects of Wettability and Surface Morphology