Abstract:This study aimed to study the interaction between two different açaí extracts used in synthesis of hybrid polymeric films based on chitosan–clay and evaluate its morphological and physical–chemical properties, indeed antibacterial and antioxidant activities. Films with acidified açai extract (FEAA) and non-acidified açai extract (FEBANA) were prepared using the casting method. It was possible to observe a surface with a rough appearance, varying according to the added extract concentration using SEM photomicrographs. The reflection peaks were similar to the Chit–Clay film (2 θ = 14° and 16.8°) and the reduction in the degree of chitosan crystallinity for the FEBANA films in relation to FEAA films. The TG data also show that the FEBANA films have a higher percentage of water of hydration than the FEAA films, corroborating this state of anhydrous films for FEAA and state of hydrated films for FEBANA. The FEBANA films were two stretches in the region between 842 and 962 cm −1 , and a shoulder 1095 cm −1 covered by bands 1025 cm −1 (Si–O–Si) and can attributed to the PEG plasticizer. This greater detection of PEG stretches in the FEBANA films suggests a greater concentration of PEG on the surface of the FEBANA film. MIC microbiology demonstrated that both types of extracts were capable of inhibiting Gram (−) strains, Escherichia coli and Pseudomonas aeruginosa , and Gram ( +) strains, Staphylococcus aureus and Staphylococcus epidermidis . In disk diffusion, the acidified extract showed inhibition activity for Edwardsiella tarda , Enterococcus faecium and Streptococcus pyogenes . Both extracts are effective in inhibiting the growth of both Gram (−) and Gram ( +) bacteria. The FEAA polymeric films showed a higher degree of recovery, reversible chemical bonding with the matrices and consequently greater DPPH free radical scavenging capacity compared to the FEBANA polymeric films. The FEAA and FEBANA films present characteristics of releasing active ingredients from the hybrid polymeric film and can be applied in edible packaging or use in biodegradable smart packaging or as food biopreservative; or even, in pharmaceutical release systems for releasing active ingredients onto the skin, as organic active ingredient release membranes for skin health and beauty, wound healing or even as adjuvants in tissue bioengineering for skin reconstruction after burns and in plastic skin surgery as biodegradable films.

Spray dried acerola (Malpighia emarginata DC) juice particles to produce phytochemical-rich starch-based edible films

Acerola byproducts microencapsulated by spray and freeze-drying: the effect of carrier agent and drying method on the production of bioactive powder

Active Edible Films Based on Arrowroot Starch with Microparticles of Blackberry Pulp Obtained by Freeze-Drying for Food Packaging

Development of Edible Coatings Based on Pineapple Peel (Ananas Comosus L.) and Yam Starch (Dioscorea alata) for Application in Acerola (Malpighia emarginata DC)

Brazilian native fruit pomace as a source of bioactive compounds on starch-based films: Antimicrobial activities and food simulator release

Effects of the spray-drying process using maltodextrin on bioactive compounds and antioxidant activity of the pulp of the tropical fruit açai (Euterpe oleracea Mart.)

Preparation and characterization of hybrid polymeric coating films of chitosan–clay loaded with açaí extract (Euterpe oleracea) for application in food and pharmaceutical areas

Biopolymers to overcome challenges in açaí pulp drying: Processing and powder quality evaluation

Purification of Arabinoxylans from Corn Fiber and Preparation of Bioactive Films for Food Packaging

Obtention of New Edible Biofilms from Water Kefir Grains in Comparison with Conventional Biofilms from Taro (Colocasia esculenta) and Cassava (Manihot esculenta) Starch

Edible film preparation by anthocyanin extract addition into acetylated cassava starch/sodium carboxymethyl cellulose matrix for oxidation inhibition of pumpkin seeds

Microencapsulation of Extracts of Strawberry (Fragaria vesca) By-Products by Spray-Drying Using Individual and Binary/Ternary Blends of Biopolymers

Acerola processing waste: Convective drying with ethanol as pretreatment

Pectin Edible Films Filled with Ilex paraguariensis Concentrate Extract and Its Characterization

Optimizing Edible Film Production from Red Pitaya Peel Powder, Konjac Glucomannan and Kappa Carrageenan

Enhancing the efficacy of Arrabidaea chica extract release from polysaccharide-based films: The impact of cashew gum and cross-linking process

Citric acid, chitosan and oregano essential oil impact on physical and antimicrobial properties of cassava starch films

Enhancing Starch Film Properties Using Bacterial Nanocellulose-Stabilized Pickering Emulsions

Intelligent films based on dual-modified starch and microencapsulated Aronia melanocarpa anthocyanins: Functionality, stability and application

Potential of Pinhão husk (Araucaria angustifolia) as a structural reinforcement agent in the properties of edible films of Pinhão flour and gelatin

The Potential of Edible Films, Sheets, and Coatings Based on Fruits and Vegetables in the Context of Sustainable Food Packaging Development