Abstract:The global massive consumption of disposable face masks driven by the ongoing COVID-19 pandemic has emerged as a blooming disaster to both the land and marine environment that might last for generations. Growing public concerns have been raised over the management and control of this new form of plastic pollution, and one of the proposed sustainable solution is to use renewable and/or biodegradable resources to develop mask materials in order to minimize their environmental impacts. As a representative biodegradable polymer, polylactic acid (PLA) has been proposed as a promising candidate to produce non-woven face masks instead of those fossil-based polymers. To further explore the feasibility of this alternative mask material, the present work aims to study both the hydrolytic and bio-degradation behaviors of pure PLA-derived 3-ply disposable face masks at ambient temperature. Hydrolytic degradability was investigated at different pH conditions of 2, 7 and 13 with the whole piece of face mask soaked for regular timed intervals up to 8 weeks. Weight loss study showed neutral and acidic conditions had minimal effect on PLA masks, but rapid degradation occurred under basic conditions in the first week with a sharp 25% decrease in weight that slowly tapered off, coupled with solution pH dropping from 13 to 9.6. This trend was supported by mechanical property, bacterial filtration efficiency (BFE) and particulate filtration efficiency (PFE) studies. Masks soaked in basic conditions had their modulus and tensile strength dropped by more than 50% after 8 weeks where the middle layer reached 68% and 90% respectively just after 48 h, and BFE and PFE decreased by 14% and 43% respectively after 4 weeks, which was much more significant than those in neutral and acidic conditions. Base degradation was also supported by nuclear magnetic resonance (NMR) and fourier transform infrared (FTIR), which disclosed that only the middle layer undergo major degradation with random chain scission and cleavage of enol or enolate chain ends, while outer and inner layers were much less affected. Scanning electron microscopy (SEM) attributed this observation to thinner PLA fibers for the middle layer of 3-7 mu m diameter, which on average is 3 times smaller. This degradation was further supported by gel permeation chromatography (GPC) which saw an increase in lower molecular weight fragment Mw similar to 800 Da with soaking duration. The biodegradation behavior was studied under OECD 301F specification in sewage sludge environment. Similarly, degradation to the middle meltblown layer was more extensive, where the average weight loss and carbon loss was 25.8% and 25.7% respectively, double that of outer/inner spunbond layer. The results showed that the face masks did not completely disintegrate after 8 weeks, but small solubilized fragments of PLA formed in the biodegradation process can be completely mineralized into carbon dioxide without generation of secondary microplastic pollution in the environment. PLA masks are therefore a slightly greener option to consider in times of a pandemic that the world was caught unprepared; however future research on masks could be geared towards a higher degradability material that fully breaks down into non-harmful components while maintaining durability, filtration and protection properties for users. (C) 2021 Published by Elsevier B.V.

Experimental design for determining the factors influencing the filtration efficiency of solution-blown spun polylactic acid filters

Development of Biodegradable Poly(butylene succinate) Based Nanofibrous Webs via Solution-Blow Spinning Technology for N95 Respiratory Filters

Non-Woven Filters Made of PLA via Solution Blowing Process for Effective Aerosol Nanoparticles Filtration

Optimization of the Centrifugal Spinning Parameters to Prepare Poly(butylene succinate) Nanofibers Mats for Aerosol Filter Applications

Regulation of Polylactic Acid Using Irradiation and Preparation of PLA–SiO2–ZnO Melt-Blown Nonwovens for Antibacterial and Air Filtration

Biodegradable Biconstituent Melt-Blown Nonwovens for Air Filtration: Fabrication and Characterization

Biodegradable and high-performance multiscale structured nanofiber membrane as mask filter media via poly(lactic acid) electrospinning

Non-Solvent Induced Phase Separation (NIPS) for Fabricating High Filtration Efficiency (FE) Polymeric Membranes for Face Mask and Air Filtration Applications

Pilot-Scale Melt Electrospinning of Polybutylene Succinate Fiber Mats for a Biobased and Biodegradable Face Mask

Preparation of porous polylactic acid nanofibers and application in non-electret high-efficiency filtration composites

3D Printed and Electrospun, Transparent, Hierarchical Polylactic Acid Mask Nanoporous Filter

Bicomponent PLA Nanofiber Nonwovens as Highly Efficient Filtration Media for Particulate Pollutants and Pathogens

Investigate the Processability of Biobased Thermoplastics Used in Nonwoven Fabrics

Electrospun Polymethylhydrosiloxane/Poly(lactic Acid) Multiscale Nanofiber Membrane with Highly Hydrophobic Interface As Material for Protective Mask Filters

Multi-layered micro/nanofibrous nonwovens for functional face mask filter

Green-Solvent-Processable Biodegradable Poly(Lactic Acid) Nanofibrous Membranes with Bead-on-String Structure for Effective Air Filtration: “Kill Two Birds with One Stone”

The Effect of Electro blow Spinning Parameters on The Characteristics of Polylactic Acid Nanofibers: Towards Green Development of High-Performance Biodegradable Membrane

Polylactic Acid Face Masks: Are These the Sustainable Solutions in Times of COVID-19 Pandemic?

A review of processing strategies to generate melt-blown nano/microfiber mats for high-efficiency filtration applications

Influence of Electrospinning Parameters on the Morphology of Electrospun Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) Fibrous Membranes and Their Application as Potential Air Filtration Materials

ZnO-PLLA/PLLA Preparation and Application in Air Filtration by Electrospinning Technology