Abstract:Additive manufacturing has undergone huge development in recent years. It has become commonplace both for the hobbyist community and industry, with important applications in several domains (e.g. biomedical, aerospace and automotive). Its main strength lies in the fact that custom parts can be quickly prototyped and manufactured, regardless of their complexity. However, many of the 3D printing techniques still have limitations in terms of strength, materials, production speed and overall usability. One of the main limitations is that most techniques utilize polymers, which are intrinsically non-conductive. This limits their use in electronics and telecommunication applications. Meanwhile, a lot of equipment used in telecommunications, such as antennas, tuners, waveguides, etc. remain very expensive due to complex and time-intensive manufacturing techniques. This leads to high prices, long lead times and limitations in the complexity of the geometries. The main goal of this research is to develop a fast and cost-effective method to produce conductive structures using additive manufacturing, more specifically fused deposition modeling (FDM) 3D printing. A special focus is put on horn antennas for microwave applications, as this application is very demanding on both the accuracy of the geometry and the conductivity of the structure. The approach in this work mainly consists of two steps: optimizing the plating conditions on flat test samples and extending this knowledge to the three-dimensional horn antenna. The chosen material is a PLA-based polymer with carbon black as an additive, which provides the polymer with some electrical conductivity (factor ~10 7 lower than copper). This conductivity is too low for any meaningful application but allows for the use of electrodeposition of copper directly onto the polymer to increase the conductivity. By focusing on reducing the distance from the electrical contact to the surface to be plated and by tuning the deposition parameters, high-quality uniform copper deposition is obtained on test samples. The achieved results outperform the current state-of-the-art in this field. The knowledge acquired from the test samples is then applied to the horn antenna. To this end a conductive antenna holder is developed. The antenna holder serves to keep the potential as constant as possible over the entire antenna surface in order to promote homogeneous deposition. It also aligns the electrodes, keeping the distance between electrodes as constant as possible and preventing short circuits. This method results in good partial coverage and again produces better results than can be found in the literature. However, direct deposition of a nicely uniform layer over the entire surface remains very challenging. An indirect electrodeposition method using conductive silver paint is used to produce the final version of the printed horn antenna. Measurements in an anechoic chamber demonstrate that the copper-coated version of the printed antenna has similar radiation performance as a commercial counterpart. An exponential horn antenna is made with decent performance, demonstrating the ease of production of more complexly shaped antennas. Our antennas can be produced within a couple of hours at a fraction of the price of commercial counterparts ($3 instead of $500-1500). This opens up new possibilities to quickly validate simulation results of new antenna designs. Further research focuses on the use of electroless plating to obtain more homogeneous copper deposition on three-dimensional structures, as well as extending our methodologies to more complex geometries.

Design, additive manufacturing and electromagnetic characterization of alumina cellular structures for waveguide antenna

Stereolithographic additive manufacturing of Luneburg lens using Al2O3-based low sintering temperature ceramics for 5G MIMO antenna

Microwave Sintering of Alumina at 915 MHz: Modeling, Process Control, and Microstructure Distribution

Effect of thermal treatments on the surface electrical conductivity of AlSi7Mg produced by laser powder bed fusion

Quality assurance thermophysical aspects of highly porous implants with cellular structure obtained by selective laser melting

Patterned Microstructure Array Fabrication By Using A Novel Standing Surface Acoustic Wave Device

A Study of Color Modulation of Porous Alumina Processed by Physical Vapor Deposition

3D-printed impedance gradient Al2O3 ceramic with in-situ growing needle-like SiC nanowires for electromagnetic wave absorption

Enhanced electromagnetic microwave absorption of SiOC ceramics targeting the integration of structure and function

Numerical Simulation of Sintering of DLP Printed Alumina Ceramics

Mechanical-electromagnetic integration design of Al 2 O 3 /SiO 2 ceramic cellular materials fabricated by digital light processing

Experimental and numerical analysis of the thermal performance of PCM-impregnated reticular structures obtained by additive manufacturing

Coupling additive manufacturing and microwave sintering: A fast processing route of alumina ceramics

Design and Manufacturing of Si-Based Non-Oxide Cellular Ceramic Structures through Indirect 3D Printing

Additive manufacturing of broadband electromagnetic wave absorbing materials: Polymer-derived SiC/Si 3 N 4 composites with triply periodic minimal surface meta-structure

Wideband High‐gain Millimetre/submillimetre Wave Antenna Using Additive Manufacturing

Manufacturing Millimeter-Wave Horn Antennas Using 3D Printing and Direct Electrodeposition

Material extrusion 3D printing of large-scale SiC honeycomb metastructure for ultra-broadband and high temperature electromagnetic wave absorption

Structural and mechanical optimization of porous alumina structures fabricated by carbon sacrificial template

Multiscale design and digital light processing preparation of high-strength SiOC ceramic metastructures for tuning microwave absorption properties

Nanoporous alumina microtubes for metamaterial and plasmonic applications