Abstract:Because of the advantages of high theoretical capacity, low cost, and environmental friendliness, lithium–sulfur (Li–S) batteries have attracted wide attention as promising energy storage system for electric vehicles and smart power grids. However, their commercialization is still greatly restricted by their poor cycle stability, resulting from the severe shuttling of soluble lithium polysulfides (LiPSs) during cycling. Herein, we designed a polymer/rGO (/rGO) blocking layer on a commercial PP separator. Such a blocking layer can strongly fix LiPSs by the electrostatic attraction effect between the cationic polymer backbones and the polysulfide anions. As a result, a Li–S battery equipped with a /rGO-functionalized separator showed much improved cycling stability with a capacity fading rate as low as 0.06% per cycle during 700 cycles at 1 C. Especially, high areal capacity of 6.3 mAh cm–2 was also achieved with a high sulfur loading of 8.5 mg cm–2 after 50 cycles. This work highly emphasizes that the electrostatic attraction mechanism between cationic polymers and polysulfides can effectively restrain the polysulfide shuttling and thus significantly improve the electrochemical performance of Li–S batteries.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.1c00281?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.1c00281</a>.SEM image of initial CNTs, TEM image and XPS survey spectrum of , SEM images and XRD patterns of GO and rGO, Raman and N2 adsorption/desorption isotherm of /rGO, Nyquist plots of /rGO separator and PP separator, CV curves and charge–discharge curves of Li–S batteries with PP separators, long-term cycling performance of the Li–S batteries with /rGO separator at 0.5 and 2 C, CV curves of Li–S batteries with /rGO separator and PP separator for the first cycle at 0.1 mV s–1, charge–discharge curves of Li–S batteries with high sulfur loading using /rGO separator and PP separator (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.1c00281/suppl_file/ae1c00281_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Reversible Switching of Battery Internal Resistance Using Iongate Separators

Draining Over Blocking: Nano‐Composite Janus Separators for Mitigating Internal Shorting of Lithium Batteries

Simultaneously Blocking Chemical Crosstalk and Internal Short Circuit via Gel-Stretching Derived Nanoporous Non-Shrinkage Separator for Safe Lithium-Ion Batteries

Separation Effect of Graphene Sheets with N, O Codoping and Molybdenum Clusters for Reversible Lithium–Iodine Batteries

Reversible Switch in Charge Storage Enabled by Selective Ion Transport in Solid Electrolyte Interphase

Boosting Battery Safety by Mitigating Thermal‐Induced Crosstalk with a Bi‐Continuous Separator

Ion-Selective Prussian-Blue-Modified Celgard Separator for High-Performance Lithium-Sulfur Battery

Reversible Li plating regulation on graphite anode through a barium sulfate nanofibers-based dielectric separator for fast charging and high-safety lithium-ion battery

Cationic-Polymer-Functionalized Separator As a High-Efficiency Polysulfide Shuttle Barrier for Long-Life Li–S Battery

Separator-Integrated, Reversely Connectable Symmetric Lithium-Ion Battery.

Ionic Selective Separator Design Enables Long‐Life Zinc–Iodine Batteries via Synergistic Anode Stabilization and Polyiodide Shuttle Suppression

Restraining Shuttle Effect in Rechargeable Batteries by Multifunctional Zeolite Coated Separator

Electronic and Ionic Co-Conductive Coating on the Separator Towards High-Performance Lithium–sulfur Batteries

Recent advances in lithium-ion battery separators with reversible/irreversible thermal shutdown capability

Promoting Reversible Redox Kinetics by Separator Architectures Based on CoS 2 /HPGC Interlayer as Efficient Polysulfide‐Trapping Shield for Li–S Batteries

An Upgraded Lithium Ion Battery Based on a Polymeric Separator Incorporated with Anode Active Materials

Converting an O-vacancy-rich Oxide into a Multifunctional Separator Modifier for Long-Lifespan Lithium Metal Batteries

Thermoregulating Separators Based on Phase‐Change Materials for Safe Lithium‐Ion Batteries

Switching Hydrophobic Interface with Ionic Valves for Reversible Zinc Batteries

Thermally Stable, Nano-Porous and Eco-Friendly Sodium Alginate/attapulgite Separator for Lithium-Ion Batteries

Advanced polyimide separator<i> via</i> co-precursor method for lithium-ion batteries with low thermal runaway risks