Abstract:The electrochemical reduction of CO2 is a promising strategy to achieve efficient conversion and utilization. In this paper, a series of Zn catalysts were prepared by electrodeposition in different atmospheric conditions (N2, CO2, H2, CO). A fibrous Zn catalyst (Zn-CO2) exhibits high electrochemical activity and stability. The Zn-CO2 catalyst shows 73.0% faradaic efficiency of CO at −1.2 V vs. RHE and the selectivity of CO almost did not change over 6 h in −1.2 V vs. RHE. The excellent selectivity and stability is attributed to the novel fibrous morphology, which increases the electrochemical active surface area. X-ray diffraction (XRD) results show that Zn-CO2 catalyst has a higher proportion of Zn (101) crystal planes, which is considered to be conducive to the production of CO. The search further demonstrates the importance of morphology control for the preparation of highly active and stable catalysts.

What problem does this paper attempt to address?

The paper primarily addresses the issue of insufficient activity and stability of catalysts in the electrochemical reduction of carbon dioxide (CO₂). Specifically, the research team prepared a series of zinc (Zn) catalysts through electrodeposition under different gas conditions (nitrogen N₂, carbon dioxide CO₂, hydrogen H₂, carbon monoxide CO) and discovered that one of the Zn-CO₂ catalysts with a fibrous structure exhibited excellent activity and stability in the electrochemical reduction of CO₂ to carbon monoxide (CO). Key points are as follows: - The Zn-CO₂ catalyst achieved a Faradaic efficiency of 73.0% for CO at a voltage of -1.2 V relative to the reversible hydrogen electrode (RHE), and this selectivity remained almost unchanged over 6 hours. - This high performance is attributed to the catalyst's unique fibrous porous structure, which increases the electrochemical active surface area (ECSA) and facilitates the adsorption and conversion of CO₂. - X-ray diffraction (XRD) results showed that the Zn-CO₂ catalyst has a higher proportion of Zn (101) crystal planes, which is believed to be beneficial for CO production. - The study indicates that during the electrodeposition of Zn in a CO₂-saturated solution, the presence of CO₂ affects the growth of Zn crystals, promoting the formation of specific morphologies and thereby enhancing the catalyst's performance. - By comparing the effective electrochemical surface area (ECSA) and Tafel slopes of different catalysts, it was further confirmed that the Zn-CO₂ catalyst has a larger surface area and similar reaction kinetics characteristics, indicating good intrinsic activity. - This work provides new ideas and methods for addressing the issues of low activity and stability in the electrochemical reduction of CO₂.

CO2-Induced Fibrous Zn Catalyst Promotes Electrochemical Reduction of CO2 to CO

Electrodeposited Zn Dendrites with Enhanced CO Selectivity for Electrocatalytic CO2 Reduction

Highly Efficient CO 2 Electroreduction on ZnN 4 -based Single-Atom Catalyst.

Atomic Zn‐Doping Induced Sabatier Optimum in NiZn0.03 Catalyst for CO2 Electroreduction at Industrial‐Level Current Densities

Layer-Stacked Zn with Abundant Corners for Selective CO2 Electroreduction to CO

Modulating Surface Zinc Species Via Facet Engineering for Efficient Electroreduction of CO2 to CO

Layer-Stacked Zn with Abundant Corners for Selective CO 2 Electroreduction to CO

Electrochemical Reduction of CO2 into Tunable Syngas Production by Regulating the Crystal Facets of Earth-Abundant Zn Catalyst.

Boosting CO 2 Electroreduction via Construction of a Stable ZnS/ZnO Interface

Fabrication of ZnO nanosheets self-assembled by nanoparticles for accelerated electrocatalytic reduction of CO2 to CO

Heterostructure of ZnO Nanosheets/Zn with a Highly Enhanced Edge Surface for Efficient CO 2 Electrochemical Reduction to CO

Atomically dispersed Ni-N-C catalyst derived from NiZn layered double hydroxides for efficient electrochemical CO 2 reduction

Hexagonal Zn Nanoplates Enclosed by Zn(100) and Zn(002) Facets for Highly Selective CO2 Electroreduction to CO

Heterostructure of ZnO Nanosheets/Zn with a Highly Enhanced Edge Surface for Efficient CO2 Electrochemical Reduction to CO.

Electrochemical CO2 Reduction to Ethanol on Zn‐Coordinated Cu Sites Formed by Atmosphere‐Induced Surface Reconstruction

Zn‐Nx Doping in Carbon Nanotubes Boosts Selective CO2 Electroreduction to CO

Local Environment-Mediated Efficient Electrocatalysis of CO2 to CO on Zn Nanosheets

Promoting CO2 Electroreduction Kinetics on Atomically Dispersed Monovalent Zn(I) Sites by Rationally Engineering Proton‐feeding Centers

Efficient electrochemical CO2 reduction to C2+ hydrocarbons on Zn-doped Cu films

Activating COOH* Intermediate by Ni/Ni3ZnC0.7 Heterostructure in Porous N-doped Carbon Nanofibers for Boosting CO2 Electroreduction

Electrochemical Reduction of CO2 to CO on Hydrophobic Zn Foam Rod in a Microchannel Electrochemical Reactor