Abstract:High temperature helium gas will provide a thermal efficiency greater than 40%, even using a conventional steam turbine. In addition, helium gas will not react chemically with blanket materials, and surrounding air and water. Tritium will be easily extracted from the coolant too. Thus, it is one of the most attractive coolants for a fusion power reactor, from the economical, safety and environmental points of view. However, a large volumetric flow rate is required owing to the small heat capacity when the pressure is not extremely high. This requires a larger reactor size, larger circulating power and more penetrations, which may increase radiation streaming. A relatively low heat transfer coefficient makes it difficult to apply to a component subjected to a high heat load, such as a divertor plate. We suggest in this study, a helium-solid suspension flow as coolant, to increase the heat capacity and heat transfer coefficient. A gas pressure of 5 MPa, and inlet and outlet temperatures of 400°C and 700°C were chosen. There are few candidates for the structural material which can be used at temperatures higher than 900°C. We have proposed an intermetallic compound of titanium aluminide (TiAl) as candidate structural material of the blanket. Although the database for TiA1 is incomplete, it has high strength and ductility at the operation temperature. Using TiA1, radioactive waste management will be mitigated, since its activity will decrease rapidly. The elongation at room temperature, which is only a few per cent, will be improved through research and development not only in fusion but also in other industrial fields. In this study, spherical pebbles of lithium oxide and small blocks of beryllium were chosen as the breeder and neutron multiplier. Manganese blocks were installed to enhance energy multiplication. A tritium breeding ratio of 1.38 and energy multiplication ratio of 1.35 were obtained with the blanket. The net plant efficiency exceeds 40%, including the circulating power. The peak surface heat flux on the divertor plate was decreased with gas puffing including an impurity near the striking point. In spite of this, the expected peak heat flux was still several MW m−2 from the result of numerical calculation of the edge plasma. To remove so high a heat load, an impinging helium-solid suspension jet was applied to the high heat flux region of the divertor plate. Molybdenum alloy was used as the structural material in this region to keep the surface temperature and thermal stress lower than the design limits. TiAl was used as the structural material of other regions in the divertor chamber. To prevent excessive sputtering erosion, the electron temperature in the divertor plasma must be kept lower than 20 eV.

A conceptual design of a spherical tokamak power plant

Conceptual design of 5 MW-NBI injector for HL-2 M tokamak

Conceptual design workflow for the STEP Prototype Powerplant

Preliminary Design of A Solid Particulate Cooled Blanket for the Steady-State Tokamak Reactor (Sstr)

Maintenance Oriented Tokamak Reactor With Low Activation Material And High Aspect Ratio Configuration

Design study of helium-solid suspension cooled blanket and divertor plate for a tokamak power reactor

Improved Tokamak Concept Focusing On Easy Maintenance

Pulsed Spherical Tokamak—A New Approach to Fusion Reactors

Flat-top plasma operational space of the STEP power plant

Fusion nuclear science facilities and pilot plants based on the spherical tokamak

Concept Design and Analysis of the Magnet System of the Sustained High Power Density Tokamak Facility

Linear gyrokinetic stability of a high $β$ non-inductive spherical tokamak

Conceptual design study for heat exhaust management in the ARC fusion pilot plant

Efficient ECCD non-inductive plasma current start-up, ramp-up, and sustainment for an ST fusion reactor

Back to the Figure-8 Stellarator

Training and Upgrading Tokamak Power Plants with Remountable Superconducting Magnets

Blanket and shield design for a noncircular Tokamak experimental power reactor

Numerical Studies and Simulation of the Lower Hybrid Waves Current Drive by using Fokker – Planck Equation in NSST and HT-7 Tokamaks

Concept design overview: a question of choices and compromise

The magnetic cage

A compact stellarator-tokamak hybrid