Abstract:A thermally sprayed deposit is formed by a stream of molten droplets impacting on a substrate followed by flattening, rapid solidification, and cooling processes. The individual molten droplets spread into thin lamellae, the stacking of which rudimentarily constitutes the thermal spray deposit. Accordingly, a thermally sprayed deposit is generally composed of lamellar structure. A portion of the deposit are voids, which constitute up to 20% of the total volume [1]. Some of the voids originated from insufficient liquid filling, prior to complete solidification, and incomplete wetting of molten liquid on the prior deposited lamella surfaces. Microcracks can be formed easily in the splats of brittle materials, in particular, ceramics owing to the quenching stresses that occur in splats [2]. Such microcracks are also a type of void within the deposits, and constitute a fraction of the overall porosity. The existence of voids in the coating will degrade the mechanical performance and corrosion resistance of thermal sprayed materials to a relatively low level compared to corresponding bulk materials. When a thermal sprayed coating is used under a certain mechanical loading, the loading may cause coating delamination or spallation in service owing to low adhesion of the coating to the substrate and limited cohesion within the coating. This undoubtedly leads to a decrease in the coating’s effective thickness or even direct exposure of the substrate surface to the operating environment. Many studies have revealed that the failure of the coating occurs readily from the interfaces among lamellae in the coating, and the interfaces between the coating and the substrate, for example, under localized load such as in abrasive wear [3] or erosion [4], fretting wear [5] and fracture mechanics test [6]. Even during the preparation of thermal sprayed samples for microstructure examination, pullouts do occur [7]. Such effect is attributed to the pores in the coating existing in the form of non-bonded lamellar interfaces [8], although in thermal barrier coatings (TBC), the performance may be improved by the existence of pores in the coating. Therefore, the modification of the microstructure of as-sprayed coating is desirable to improve coating performance. Up to now, many attempts

Estimating and reducing dissipative losses in thermal spray: A parametrized material flow analysis approach

Investigation of Structural Integrity and Life Time Prediction of the Thermal Sprayed Alloy Coating for Remanufacturing

Exploring thermal dynamics and porosity of cold-sprayed Ti-6Al-4V coatings on Al6061-T6 substrates: A pulsed thermography and numerical modeling approach

An experimentally validated dislocation density based computational framework for predicting microstructural evolution in cold spray process

Strategy to Generate Oxide-Free Molten Metal Droplets for Fully Dense Corrosion-Resistant Coatings by Atmospheric Plasma Spraying

Computer design of thermal sprayed metal powder coatings

Optimization of Thermal Spray Parameters of NiAl/Cr2C3 Coating by Taguchi Method

PREDICTION AND CONTROL OF RESIDUAL STRESSES IN THERMAL SPRAYED COATINGS

Numerical Investigation of YSZ Droplet Impact on a Heated Wall for Thermal Spray Application

A numerical model-based deposition strategy for heat input regulation during plasma arc-based additive manufacturing

Thermal effect of high-velocity particle impingements on coating quality in cold gas dynamic spray operations

Design and Development of Cost-Effective Equipment for Tribological Evaluation of Thermally Sprayed Abradable Coatings

Integral Numerical Modeling of the Deposition Profile of a Cold Spraying Process As an Additive Manufacturing Technology

Stripping of Thermal Sprayed Oxid Coatings by Means of Laser Techniques, Water Jet and a Newly Developed Hybrid Method

Effect of Droplet Initial Temperature on Substrate Melting and Its Re-solidification in Plasma Spray Process

Modeling of the residual stresses in plasma-spraying functionally graded ZrO2/NiCoCrAlY coatings using finite element method

Application of Functionally Graded Interlayer on Reducing the Residual Stress Discontinuities at Interfaces Within a Plasma-Sprayed Thermal Barrier Coating

Influence of processing conditions on the mechanical, tribological and fatigue performance of cold spray coating: a review

A computational and experimental approach to understanding material flow behavior during additive friction stir deposition (AFSD)

Effects of Plume Targeted Cooling on Residual Stress in Controlled Atmosphere Plasma Sprayed Coatings

Potential strengthening of erosion performance of plasma-sprayed Al2O3 coating by adhesives impregnation