Abstract:Combustion of titanium alloy is a typical catastrophic failure of modern aeroengine. The abnormal friction between compressor rotor and stator is the main ignition source. A thermal theory model with friction heat source of titanium alloy is established based on the theory of heterogeneous ignition. The corresponding equation of critical temperature and ignition delay time are derived. The difference between the frictional ignition model and the classic model is discussed. The concept of critical heat generation temperature is proposed. The difference from the heterogeneous ignition model, and the effects of friction coefficient, oxygen concentration, flow velocity, contact radius and flame retardant layer thickness on the ignition parameters are analyzed. The research result shows that when the instantaneous temperature of the contact surface is lower than the critical heat temperature, the heat generation process is dominated by frictional heat, and when the temperature is higher than the critical heat temperature, the heat generation process is dominated by chemical reaction heat, that reducing the coefficient of friction can dramatically increase the critical temperature, but the change of friction coefficient has very little effect on the ignition delay time which can be ignored, that the critical temperature decreases significantly with the increase of oxygen concentration and the decrease of flow velocity. When the oxygen concentration increases from 21% to 42% and the flow velocity decreases from 310 m/s to 50 m/s, the critical temperature decreases by about 213 K and 197 K, respectively. The relative error between the experimental result and the theoretical result is 8.3%, which verifies the reliability of the model. The contact area has an effect on friction heat generation, reaction heat generation, and surface heat dissipation, and has a great influence on the critical temperature. The critical temperature decreases exponentially with contact radius increasing. When the contact radius increases to 0.007 m, the ignition temperature of the titanium alloy and its flame retardant layer are 899 K and 988 K, respectively. The increase of the thickness of flame retardant layer can effectively improve the critical temperature and ignition delay time. The critical temperature of titanium alloy with flame retardant layer is increased by about 172 K, and the ignition delay time is increased by about 3 s.

Frictional ignition of dispersion-strengthened Ni-Cr alloys

Molecular Dynamic Simulations of Ti-6Al and Fe-12Cr Alloys for Their Heat Transfer and Oxygen Transport Behaviors

Theoretical Study on Ignition of Titanium Alloy under High Temperature Friction Condition

Combustion Microstructures and Frictional Ignition Resistance of Ti-6Al-4V Titanium Alloy

Aluminum Particle Ignition Studies with Focus on Effect of Oxide Barrier

Investigation on the Oxidation Behavior of the NiCrAlY Bond-Coat with Low Al Content Sprayed by High Velocity Oxygen Fuel Method

Preparation of a novel laser cladding Ni-based alloy with promising applications in high-temperature conditions: Genetic design, multi-phase evolution, and synergy mechanism

Plasma Spraying NiCoCrAlY-Cr2O3-AgMo Coatings: Fabrication and Tribological Mechanisms

Cyclic and Isothermal Oxidation Behavior of a Directionally Solidified Ni-Al-Ti-Co-Cr Superalloy

In Situ Reactive Formation of Mixed Oxides in Additively Manufactured Cobalt Alloy

Microstructure Evolution and Oxidation Resistance Properties of Oxide Dispersion Strengthened FeCrAl Alloys at 1100 °C

On the Oxidation and Interdiffusion Behavior of an AlCoCrFeNiY High-Entropy Alloy Bond Coat on a Directionally Solidified Ni-based Superalloy

Flame-retardant mechanism of TiAl alloy by frictional ignition method

The Role of Target Melting in Particle Impact Ignition with Inert Particulate

Dynamics of early-stage oxide formation on a Ni-Cr-Mo alloy

Wear and Friction Behavior of Plasma Sprayed NiCrMo-NiCrBSi Alloy Anti-Friction Coatings

Improved ignition and combustion performances of aluminum nanoparticles by in-situ partial conversion of native alumina to surface Al-MOF shell

Oxidation behavior at 1100 °C of NiCrAlY coatings deposited by various PVD techniques

Elucidating friction properties and strengthening mechanisms of Ni-based surfacing layer containing 9R phase

Effect of Feedstock Powder Intrinsic Characteristics on the Tribological Behavior of Inductively Remelted NiCrBSi Flame-Sprayed Coatings

Tribological Behavior of In-Situ (cr, Mo)/Fe3al-20 Wt.%Al2o3 Composites at Elevated Temperatures