Raman mapping of piezoelectric poly( l -lactic acid) films for force sensors

Ivan S Babichuk,Chubin Lin,Yuhui Qiu,Huiyu Zhu,Terry Tao Ye,Zhaoli Gao,Jian Yang,Ivan S. Babichuk

DOI: https://doi.org/10.1039/d2ra04241j

IF: 4.036

2022-01-01

RSC Advances

Abstract:Poly- l -lactic acid (PLLA) is a synthetic, biocompatible, biodegradable polymer with good piezoelectric properties.

chemistry, multidisciplinary

What problem does this paper attempt to address?

Hierarchically Structured Hollow PVDF Nanofibers for Flexible Piezoelectric Sensor

Qunyao Zhang,Jianhui Li,Guangyong Li,Jianke Du,Chao Xie,Hui Li,Yuan Jin,Yong He

DOI: https://doi.org/10.1016/j.cej.2024.155661

IF: 15.1

2024-01-01

Chemical Engineering Journal

Abstract:The emergence of flexible sensors addresses the limitations of traditional detection equipment, such as large size, high cost, and inconvenient portability. These sensors have significantly advanced the development of wearable electronic devices for applications in electronic skin, energy harvesting, and energy storage. To enhance the sensitivity of flexible sensors, we developed a hierarchical polyvinylidene fluoride (PVDF) nanofiber-based piezoelectric sensor. By utilizing coaxial electrospinning, we fabricated nanofibers with hollow interiors and porous outer walls. Additionally, microstructures were constructed on the fiber membrane surface by modifying the collector's shape. The resulting microstructured hollow PVDF nanofiber membrane exhibited high beta-phase content (91.31 %), excellent flexibility (maximum strain 56.9 %), and high porosity (88.94 %). The sensor demonstrated a sensitivity of 2.7 V/N (1.08 V/kPa) and a maximum output voltage of 10.1 V, approximately three times higher than that of solid PVDF nanofibers without microstructures. Even after 14,400 cycles of impact, the sensor maintained stable output. The sensor was successfully applied to human activity monitoring and gesture recognition, showcasing its ability to monitor various human activities, respond rapidly (60.4 ms), and synchronously control a mechanical palm to perform different gestures. This work highlights the potential of hierarchically structured hollow PVDF nanofibers in advancing the performance and application scope of flexible piezoelectric sensors.
Ferroelectric Thin-Film Active Sensors for Structural Health Monitoring

Bin Lin,Victor Giurgiutiu,Zheng Yuan,Jian Liu,Chonglin Chen,Jiechao Jiang,Amar S. Bhalla,Ruyan Guo

DOI: https://doi.org/10.1117/12.714862

2007-01-01

Abstract:Piezoelectric wafer active sensors (PWAS) have been proven a valuable tool in structural health monitoring. Piezoelectric wafer active sensors are able to send and receive guided Lamb/Rayleigh waves that scan the structure and detect the presence of incipient cracks and structural damage. In-situ thin-film active sensor deposition can eliminate the bonding layer to improve the durability issue and reduce the acoustic impedance mismatch. Ferroelectric thin films have been shown to have piezoelectric properties that are close to those of single-crystal ferroelectrics but the fabrication of ferroelectric thin films on structural materials (steel, aluminum, titanium, etc.) has not been yet attempted. In this work, in-situ fabrication method of piezoelectric thin-film active sensors arrays was developed using the nano technology approach. Specification for the piezoelectric thin-film active sensors arrays was based on electro-mechanical-acoustical model. Ferroelectric BaTiO3 (BTO) thin films were successfully deposited on Ni tapes by pulsed laser deposition under the optimal synthesis conditions. Microstructural studies by X-ray diffractometer and transmission electron microscopy reveal that the as-grown BTO thin films have the nanopillar structures with an average size of approximately 80 nm in diameter and the good interface structures with no inter-diffusion or reaction. The dielectric and ferroelectric property measurements exhibit that the BTO films have a relatively large dielectric constant, a small dielectric loss, and an extremely large piezoelectric response with a symmetric hysteresis loop. The research objective is to develop the fabrication and optimum design of thin-film active sensor arrays for structural health monitoring applications. The short wavelengths of the micro phased arrays will permit the phased-array imaging of smaller parts and smaller damage than is currently not possible with existing technology.
Skin‐Adhesive Flexible Force Sensors Based on Piezoelectric Poly(l‐lactic acid) for Human Behavior Recognition

Chubin Lin,Wenjin Wu,Huiyu Zhu,Yuhui Qiu,Shaolong Cui,Weiquan Chen,Ivan S. Babichuk,Terry Tao Ye,Zhaoli Gao,Jian Yang

DOI: https://doi.org/10.1002/admt.202202142

IF: 6.8

2023-04-07

Advanced Materials Technologies

Abstract:In this work, first time the relationships between the performances of the piezoelectric sensors are combined with flexible skin‐adhesive substrate for human behavior recognition and the physical properties of the poly‐l‐lactic acid (PLLA) films. The intensity of the piezoelectric signal of the sensor based on the PLLA film is influenced by its structural features in the synthesis and postsynthesized processing. The application of biodegradable films based on the piezoelectric effect of poly‐l‐lactic acid (PLLA) in sensors, transducers, actuators, and so on has gradually become one of the emerging research focuses. In this work, a flexible PLLA sensor with UV‐curable acrylate film packaging is proposed for human behavior recognition. The acrylic films with different proportions have different mechanical and surface properties, showing good flexibility, ductility, and skin adhesion. The morphology and crystal structure of the PLLA films and UV curable substrate obtained under the various postprocessing conditions and different proportions are examined by scanning electron microscopy, X‐ray diffraction, Raman, and ATR‐FTIR spectroscopy. In addition, by comparing six groups of PLLA films with different treatment conditions, the device made on film stretched four times and annealed for 8 h has the best performance. This sensor has good response ability to impact, vibration, and bending strain, and can be applied to human behavior recognition, such as touch, wrist bending, and swallowing.

materials science, multidisciplinary
High piezoelectric performance of poly(lactic acid) film manufactured by solid-state extrusion

Mitsunobu Yoshida,Takayuki Onogi,Katsuki Onishi,Takuma Inagaki,Yoshiro Tajitsu

DOI: https://doi.org/10.7567/jjap.53.09pc02

IF: 1.5

2014-09-01

Japanese Journal of Applied Physics

Abstract:Recently, the application of uniaxially stretched poly(l-lactic acid) (PLLA) films to speakers, actuators, and pressure sensors has been attempted, taking advantage of their piezoelectric performance. However, the shear piezoelectric constant d14 of uniaxially stretched PLLA film is conventionally 6–10 pC N−1. To realize a high sensitivity of pressure sensors, compact speakers, and actuators, and a low driving voltage, further improvement of the piezoelectric performance is desired. In this study, we carried out solid-state extrusion (SSE) to stretch and orient poly(d-lactic acid) (PDLA) and verified its effects on piezoelectric performance. By SSE, we were able to improve the mechanical strength and elastic modulus of PDLA samples. Furthermore, the d14 of the samples was significantly increased to approximately 20 pC N−1.

physics, applied
Electrospun Environment‐Friendly Poly (L‐Lactic Acid)/CO2‐Based Polyurea Nanofiber Film for Piezoelectric Sensor

Xiaoxia Gu,Meng Cui,Bin Wang,Chenghao Zhang,Yanlong Zhu,Xu Jin,Rui Wang,Xiuqin Zhang

DOI: https://doi.org/10.1002/adsu.202200441

IF: 6.737

2023-03-19

Advanced Sustainable Systems

Abstract:PU/PLLA electrospun nanofiber film is prepared by combining poly (L‐lactic acid) (PLLA) with CO2‐based polyurea (PU) synthesized from CO2 and diamine. This is the first report on the preparation of composite piezoelectric materials using CO2‐based polymer and PLLA. The piezoelectric performance of the PU/PLLA sensor is high, exhibiting potential application in the field of intelligent wearable devices. Developing piezoelectric polymers which have environmental‐friendly raw material resources and can be used for wearable electronic devices, are of great significance for reducing dependence on fossil energy and achieving the goal of carbon neutrality. Poly (L‐lactic acid) (PLLA) is a bio‐based piezoelectric polymer and has important research value. To optimize the properties of materials, electrospinning technology is used for preparing nanofiber films by combining PLLA with CO2‐based polyurea (PU) synthesized from CO2 and diamine, and assembling the piezoelectric sensors. The results show that when the amount of PU is 16 wt%, the voltage of the PU/PLLA piezoelectric sensor is 19 V, which is 15 times that of the PLLA piezoelectric sensor and has good stability and durability. The high dipole moment of NHCONH in PU and the synergistic effect between PU and PLLA are the keys to improving the piezoelectric property of nanofiber film. This is the first report on the preparation of composite piezoelectric materials using CO2‐based polymer and PLLA. PU/PLLA piezoelectric sensor can produce a good piezoelectric response to human vital signs and motion states. As a self‐powered sensor, it has potential application in the field of intelligent wearable devices.

materials science, multidisciplinary,green & sustainable science & technology
Filler-Enhanced Piezoelectricity of Poly-L-Lactide and Its Use as a Functional Ultrasound-Activated Biomaterial

Marija Vukomanović,Lea Gazvoda,Mario Kurtjak,Marjeta Maček-Kržmanc,Matjaž Spreitzer,Qiao Tang,Jiang Wu,Hao Ye,Xiangzhong Chen,Michele Mattera,Josep Puigmartí-Luis,Salvador Vidal Pane

DOI: https://doi.org/10.1002/smll.202301981

IF: 13.3

Small

Abstract:Poly-L-lactide (PLLA) offers a unique possibility for processing into biocompatible, biodegradable, and implantable piezoelectric structures. With such properties, PLLA has potential to be used as an advanced tool for mimicking biophysical processes that naturally occur during the self-repair of wounds and damaged tissues, including electrostimulated regeneration. The piezoelectricity of PLLA strongly depends on the possibility of controlling its crystallinity and molecular orientation. Here, it is shown that modifying PLLA with a small amount (1 wt%) of crystalline filler particles with a high aspect ratio, which act as nucleating agents during drawing-induced crystallization, promotes the formation of highly crystalline and oriented PLLA structures. This increases their piezoelectricity, and the filler-modified PLLA films provide a 20-fold larger voltage output than nonmodified PLLA during ultrasound (US)-assisted activation. With 99% PLLA content, the ability of the films to produce reactive oxygen species (ROS) and increase the local temperature during interactions with US is shown to be very low. US-assisted piezostimulation of adherent cells directly attach to their surface (such as skin keratinocytes), stimulate cytoskeleton formation, and as a result cells elongate and orient themselves in a specific direction that align with the direction of PLLA film drawing and PLLA dipole orientation.
A correlation study on piezo-embedded carbon fibre reinforced polylactic acid composite: Experimental and numerical modelling

Jerold John Britto John Peter Antony,Vasanthanathan Arunachalam,Senthilkumar Krishnasamy,Sanjay Mavinkere Rangappa,Suchart Siengchin

DOI: https://doi.org/10.1177/08927057241231715

IF: 3.0272

2024-02-11

Journal of Thermoplastic Composite Materials

Abstract:Journal of Thermoplastic Composite Materials, Ahead of Print. In this research work, a piezoelectric sensor and actuator model was designed. Carbon fibre-reinforced polylactic acid (CF/PLA) composites were fabricated using the fused deposition modelling (FDM) technique using many parameters to achieve this goal. For instance, the primary key parameters were 0.1 mm (layer height) and 25 mm/s (print head). Besides, the fabricated samples were subjected to a tensile study. Besides, MATLAB® Partial Differential Equation (PDE) tool was used to develop a finite element analysis (FEA) model for the piezoelectric actuator using the experimentally tested results. The MATLAB® was also used to examine the geometry and tip deflection. The experimental works were carried out to measure the sample's strain using piezoelectric sensors. This approach could be used to establish the accuracy of the model. The CF/PLA composites were fabricated using 20 wt.% of reinforcements. The experimental results and finite element simulation were good agreement on results. Results reported that the deflections of 6.5765 mm, 5.197 mm, and 7.6328 mm, respectively embedded with PZT 5J, PZT 5H, and PZT 5A.

materials science, composites
High Performance Piezoelectric Polymer Film with Aligned Electroactive Phase Nanofibrils Achieved by Melt Stretching of Slightly Crosslinked Poly(vinylidene Fluoride) for Sensor Applications

Bin Chen,Ming Yuan,Ruixue Ma,Xiaohui Wang,Wei Cao,Chuntai Liu,Changyu Shen,Zhen Wang

DOI: https://doi.org/10.1016/j.cej.2021.134475

IF: 15.1

2022-01-01

Chemical Engineering Journal

Abstract:Flexible, transparent and lightweight polymer piezoelectric films are promising for emerging sensor applications, including wearable electronics and human-machine interfaces. However, it remains a great challenge for largescale fabrication of high-quality polymer piezoelectric films by a cost-effective melt processing approach, mainly due to the difficulty of acquiring well-defined electroactive phases. Herein, a readily implementable and scalable strategy is reported to achieve poly(vinylidene fluoride) (PVDF) film with ultrahigh content of electroactive beta-phase (-96%) via melt stretching of slightly crosslinked PVDF. Upon controlled temperature and stretch ratio, the beta-phase adopts an oriented nanofibril (diameter, 21.6 nm) morphology, while nanofibrils are further densely and parallelly aligned to fill the film space. The hierarchical nanoscale phase morphology endows the slightly crosslinked film with high optical transmittance (-90%), good flexibility and also superior mechanical properties. Moreover, flexible piezoelectric device constructed on the film is demonstrated to have excellent electrical output with sensitive and repeatable responses in sensing dynamic pressure (0-250 kPa), temperature variation (3.3 mV C-1), human motions and subtle physiological activities. This study therefore paves the way towards scalable manufacturing of high-performance piezoelectric polymer film through simple melt stretching.
Fundamental study on improvement of piezoelectricity of poly(ι-lactic acid) and its application to film actuators

Yoshiro Tajitsu

DOI: https://doi.org/10.1109/TUFFC.2013.2744

Abstract:We designed a new film actuator, whose driving force is generated by a surface wave, which induces rotational motion. Its performance is similar to that of a rotation motor even though the new film actuator has no complex mechanical parts. To realize the film actuator, we used a poly(l-lactic acid) (PLLA) film with improved piezoelectricity. First, we theoretically investigated the necessary conditions for a surface wave to be generated on the end face of a PLLA film by the fusion of its shear piezoelectricity and resonance, and then experimentally realized this. Using the actuator made using the PLLA film, we demonstrated that the clockwise and counterclockwise rotation of an object placed on the end face of the PLLA film actuator could be freely controlled by changing the frequency of the ac voltage applied to the actuator.
Flexible Piezoelectric Tactile Sensor Array For Dynamic Three-Axis Force Measurement

Ping Yu,Weiting Liu,Chunxin Gu,Xiaoying Cheng,Xin Fu

DOI: https://doi.org/10.3390/s16060819

IF: 3.9

2016-01-01

Sensors

Abstract:A new flexible piezoelectric tactile sensor array based on polyvinylidene fluoride (PVDF) film is proposed for measuring three-axis dynamic contact force distribution. The array consists of six tactile units arranged as a 3 x 2 matrix with spacing 8 mm between neighbor units. In each unit, a PVDF film is sandwiched between four square-shaped upper electrodes and one square-shaped lower electrode, forming four piezoelectric capacitors. A truncated pyramid bump is located above the four piezoelectric capacitors to improve force transmission. A three-axis contact force transmitted from the top of the bump will lead to the four piezoelectric capacitors underneath undergoing different charge changes, from which the normal and shear components of the force can be calculated. A series of dynamic tests have been carried out by exerting sinusoidal forces with amplitudes ranging from 0 to 0.5 N in the x-axis, 0 to 0.5 N in the y-axis, and 0 to 1.5 N in the z-axis, separately. The tactile units show good sensitivities with 14.93, 14.92, and 6.62 pC/N in the x-, y-, and z-axes, respectively. They can work with good linearity, relatively low coupling effect, high repeatability, and acceptable frequency response in the range of 5-400 Hz to both normal and shear load. In addition, dynamic three-axis force measurement has been conducted for all of the tactile units. The average errors between the applied and calculated forces are 10.68% +/- 6.84%. Furthermore, the sensor array can be easily integrated onto a curved surface, such as robotic and prosthetic hands, due to its excellent flexibility.
On the Nanoscale Mapping of the Mechanical and Piezoelectric Properties of Poly (L-Lactic Acid) Electrospun Nanofibers

Nguyen Thai Cuong,Sophie Barrau,Malo Dufay,Nicolas Tabary,Antonio Da Costa,Anthony Ferri,Roberto Lazzaroni,Jean-Marie Raquez,Philippe Leclère

DOI: https://doi.org/10.3390/app10020652

2020-01-16

Applied Sciences

Abstract:The effect of the post-annealing process on different properties of poly (L-lactic acid) (PLLA) nanofibers has been investigated in view of their use in energy-harvesting devices. Polymeric PLLA nanofibers were prepared by using electrospinning and then were thermally treated above their glass transition. A detailed comparison between as-spun (amorphous) and annealed (semi-crystalline) samples was performed in terms of the crystallinity, morphology and mechanical as well as piezoelectric properties using a multi-technique approach combining DSC, XRD, FTIR, and AFM measurements. A significant increase in the crystallinity of PLLA nanofibers has been observed after the post-annealing process, together with a major improvement of the mechanical and piezoelectric properties.
Piezoelectric Polyacrylonitrile Nanofiber Film-Based Dual-Function Self-Powered Flexible Sensor.

Gengrui Zhao,Xiaodi Zhang,Xin Cuo,Shu Wang,Zhirong Liu,Lin Deng,Anhui Qi,Xiran Qiao,Lijie Li,Caofeng Pan,Yan Zhang,Linlin Li

DOI: https://doi.org/10.1021/acsami.8b02564

IF: 9.5

2018-01-01

ACS Applied Materials & Interfaces

Abstract:To meet the growing demands in flexible and wearable electronics, various sensors have been designed for detecting and monitoring the physical quantity changes. However, most of these sensors can only detect one certain kind of physical quantity based on a single mechanism. In this paper, we have fabricated a multifunctional sensor made from carbonized electrospun polyacrylonitrile/barium titanate (PAN-C/BTO) nanofiber film. It can detect two physical quantities (pressure and curvature), independently and simultaneously, by integrating piezoresistive, piezoelectric, and triboelectric effects. For flex sensing with the impedance change of PAN-C/BTO nanofiber films during bending, it had a sensitivity of 1.12 deg-1 from 58.9° to 120.2° and a working range of 28°-150°. For self-powered force sensing, it had a gauge factor of 1.44 V·N-1 within the range of 0.15-25 N. The sensor had a long stability over 60 000 cycles at both sensing modes. The inclusion of barium titanate nanoparticles (BTO NPs) into the nanofiber film had an over 2.4 times enhancement of sensitivity for pressure sensing because of the synergy of piezoelectric and triboelectric effects. On the basis of multifunction and modularity, a series of potential applications of the sensor were demonstrated, including sensing human's swallowing, walking gaits, finger flexure, and finger-tapping. The self-powered flexible dual-mode sensor has great application potential in human-computer interactive and smart wearable sensing systems.
Conjugated Polymer Films for Piezoresistive Stress Sensing

Zhong, G.Y.,Zhang, Y.Q.,Cao, X.A.

DOI: https://doi.org/10.1109/LED.2009.2031255

2009-01-01

Abstract:The changes in the electrical conductivity of an indium-tin-oxide/poly [2-methoxy-5-(2'-ethylhexyloxy)-1,4-phyenylenevinylene] (MEH-PPV)/Al structure under compressive stresses were measured. The current recorded at 3 V showed a nearly linear characteristic response between 0.25 and 1.1 MPa with a sensitivity of 5.0 muA/KPa and a maximal piezoresistance coefficient of ~1.1 times 10-4 Pa-1. The devices under compression exhibited resistive switching above a threshold voltage with a resistance ratio of five, suggesting that the formation of nanofilamentary chains may be another mechanism in addition to increased intermolecular electron hopping contributing to the stress-induced current changes. The single-layer MEH-PPV sensors also exemplified good stability and repeatability, and appear to be promising for tactile sensing applications.
High Performance Piezoelectric Devices Based on Aligned Arrays of Nanofibers of Poly[(vinylidenefluoride-co-trifluoroethylene]

Luana Persano,Canan Dagdeviren,Yewang Su,Yihui Zhang,Salvatore Girardo,Dario Pisignano,Yonggang Huang,John A. Rogers

DOI: https://doi.org/10.1038/ncomms2639

2013-09-27

Abstract:Multifunctional capability, flexible design, rugged lightweight construction, and self-powered operation are desired attributes for electronics that directly interface with the human body or with advanced robotic systems. For these and related applications, piezoelectric materials, in forms that offer the ability to bend and stretch, are attractive for pressure/force sensors and mechanical energy harvesters. In this paper we introduce a large area, flexible piezoelectric material that consists of sheets of electrospun fibers of the polymer poly[(vinylidenefluoride-co-trifluoroethylene]. The flow and mechanical conditions associated with the spinning process yield free-standing, three-dimensional architectures of aligned arrangements of such fibers, in which the polymer chains adopt strongly preferential orientations. The resulting material offers exceptional piezoelectric characteristics, to enable, as an example, ultra-high sensitivity for measuring pressure, even at exceptionally small values (0.1 Pa). Quantitative analysis provides detailed insights into the pressure sensing mechanisms, and engineering design rules. Applications range from self-powered micro-mechanical elements, to self-balancing robots and sensitive impact detectors.

Materials Science
Polylactic Acid Piezo-Biopolymers: Chemistry, Structural Evolution, Fabrication Methods, and Tissue Engineering Applications

Amirhossein Farahani,Abbas Zarei-Hanzaki,Hamid Reza Abedi,Lobat Tayebi,Ebrahim Mostafavi

DOI: https://doi.org/10.3390/jfb12040071

2021-12-08

Abstract:Polylactide acid (PLA), as an FDA-approved biomaterial, has been widely applied due to its unique merits, such as its biocompatibility, biodegradability, and piezoelectricity. Numerous utilizations, including sensors, actuators, and bio-application-its most exciting application to promote cell migration, differentiation, growth, and protein-surface interaction-originate from the piezoelectricity effect. Since PLA exhibits piezoelectricity in both crystalline structure and an amorphous state, it is crucial to study it closely to understand the source of such a phenomenon. In this respect, in the current study, we first reviewed the methods promoting piezoelectricity. The present work is a comprehensive review that was conducted to promote the low piezoelectric constant of PLA in numerous procedures. In this respect, its chemistry and structural origins have been explored in detail. Combining any other variables to induce a specific application or to improve any PLA barriers, namely, its hydrophobicity, poor electrical conductivity, or the tuning of its mechanical properties, especially in the application of cardiovascular tissue engineering, is also discussed wherever relevant.
Uniaxially drawn poly (L-lactic acid)/ poly (vinylidene fluoride) polymer blend as a promising piezoelectric material: Hysteresis and resonance spectroscopy study

N.I. Mukri,T.S. Velayutham,W.H. Abd Majid,S.H. Mat Zin

DOI: https://doi.org/10.1016/j.molstruc.2024.138253

IF: 3.841

2024-04-26

Journal of Molecular Structure

Abstract:This study explores the potential for piezoelectricity in a blend of polyvinylidene fluoride (PVDF) and poly- L -lactic acid (PLLA) prepared using the solution casting method. Dielectric frequency measurements across a range of 10 2 to 10 6 Hz revealed piezoelectric resonance within a broader dielectric relaxation regime. Analysis of the resonance spectra for length and width vibrational modes enabled the determination of the piezoelectric tensor components of the PVDF/PLLA blend. The blend exhibited enhanced ferroelectric polarization reversal, remnant polarization, and coercive field compared to pristine PVDF samples. The piezoelectric constants d 31 and d 14 ( d 36 of the blend) were determined. Mechanical drawing and poling techniques were employed to generate multiple piezoelectric constants, allowing for efficient energy harvesting from various directions. This flexible blend offers promising prospects for versatile energy conversion applications.

chemistry, physical
Flexible Piezoelectric 0–3 PZT@C/PDMS Composite Films for Pressure Sensor and Limb Motion Monitoring

Chungang Li,Chao Li,Yingzi Wang,Yaoting Zhao,Fengzhen Yang,Gensheng Dong,Xiujuan Lin,Shifeng Huang,Changhong Yang

DOI: https://doi.org/10.3390/coatings14101269

IF: 3.236

2024-10-04

Coatings

Abstract:The flexible piezoelectric pressure sensor is essential in areas such as machine sensing and human activity monitoring. Here, 0-dimensional PZT piezoelectric ceramic nanoparticles with carbon coating were synthesized by a surface-modified technique. The excellent electrical conductivity of the carbon shell causes redistribution and accumulation of mobile charges in the carbon layer, resulting in a greatly increased piezoelectric effect by inducing an enhanced electric field. A series of organic–inorganic composite films were prepared by the spin-coating method using polydimethylsiloxane (PDMS) as the matrix. The as-fabricated flexible PZT@C/PDMS composite film with 40 wt% PZT@C powder exhibits an excellent output voltage of ~74 V, a peak of output current ~295 nA, as well as a big sensitivity of 5.26 V N−1. Moreover, the composite film can be used as a pressure sensor to detect changes in force as well as for monitoring limb movements such as finger flexion, wrist flexion, and pedaling. This study reveals the promising applications of flexible 40%PZT@C/PDMS composite film for limb motion monitoring and pressure sensing.

materials science, multidisciplinary,physics, applied, coatings & films
Ultrastable piezoelectric biomaterial nanofibers and fabrics as an implantable and conformal electromechanical sensor patch

Tong Li,Yongjiu Yuan,Long Gu,Jun Li,Yan Shao,Shan Yan,Yunhe Zhao,Corey Carlos,Yutao Dong,Hong Qian,Xiong Wang,Wenlong Wu,Steven Wang,Zuankai Wang,Xudong Wang

DOI: https://doi.org/10.1126/sciadv.adn8706

IF: 13.6

2024-07-20

Science Advances

Abstract:Poly( l -lactic acid) (PLLA) is a widely used U.S. Food and Drug Administration–approved implantable biomaterial that also possesses strong piezoelectricity. However, the intrinsically low stability of its high-energy piezoelectric β phase and random domain orientations associated with current synthesis approaches remain a critical roadblock to practical applications. Here, we report an interfacial anchoring strategy for fabricating core/shell PLLA/glycine (Gly) nanofibers (NFs) by electrospinning, which show a high ratio of piezoelectric β phase and excellent orientation alignment. The self-assembled core/shell structure offers strong intermolecular interactions between the -OH groups on Gly and C=O groups on PLLA, which promotes the crystallization of oriented PLLA polymer chains and stabilizes the β phase structure. As-received core/shell NFs exhibit substantially enhanced piezoelectric performance and excellent stability. An all NF–based nonwoven fabric is fabricated and assembled as a flexible nanogenerator. The device offers excellent conformality to heavily wrinkled surfaces and thus can precisely detect complex physiological motions often found from biological organs.

multidisciplinary sciences
High-Performance Flexible PLA/BTO-Based Pressure Sensor for Motion Monitoring and Human–Computer Interaction

Xuguang Sui,Qingmiao Mu,Jia Li,Bo Zhao,Hongxi Gu,Han Yu,Juan Du,Lijun Ren,Dengwei Hu

DOI: https://doi.org/10.3390/bios14100508

2024-10-18

Biosensors

Abstract:Flexible electronics show wide application prospects in electronic skin, health monitoring, and human–machine interfacing. As an essential part of flexible electronics, flexible pressure sensors have become a compelling subject of academic research. There is an urgent need to develop piezoelectric sensors with high sensitivity and stability. In this work, the high flexibility of polylactic acid (PLA) film and the excellent ferroelectric properties and high dielectric constant of tetragonal barium titanate (BTO) led to their use as filling materials to fabricate flexible piezoelectric composite films by spinning coating. PLA is used to produce flexible binding substrates, and BTO is added to the composite to enhance its electrical output by improving its piezoelectric performance. The peak output voltage of the PLA/BTO tetragonal piezoelectric film is 22.57 V, and the maximum short-circuit current was 3041 nA. Durability tests showed that during 40,000 s of continuous operation, in the range of 15~120 kPa, the linear relationship between pressure and the film was excellent, the sensitivity for the output voltage is 0.176 V/kPa, and the output current is 27.77 nA/kPa. The piezoelectric pressure sensor (PPS) also enables accurate motion detection, and the extensive capabilities of the PENG highlight its potential in advancing motion sensing and human–computer interactions.

chemistry, analytical,nanoscience & nanotechnology,instruments & instrumentation
Microactuators with Piezoelectric Polylactic Acid Fibers—Toward the Realization of Tweezers for Biological Cells

Y. TAJITSU,S. KAWAI,M. KANESAKI,M. DATE,E. FUKADA

DOI: https://doi.org/10.1080/00150190490460885

2004-01-01

Ferroelectrics

Abstract:The poly-L-lactic acid (PLLA) shows a high shear piezoelectric constant. We fabricated PLLA fiber samples with large degree of crystallinity and high orientation of crystallites using high-speed spinning. If the electric field is applied to the PLLA fiber in the direction perpendicular to the PLLA fiber axis, the PLLA fiber must be driven by the piezoelectric effect. Therefore, we devised an effective method of applying the electric field to the PLLA fiber. We also developed equipment for measuring the piezoelectric motion of the PLLA fiber, which uses a CCD camera and divided photodiodes. As a result, we could drive the PLLA fiber by the shear piezoelectric effect under the application of ac voltage, and observed the bending motion of the entire PLLA fiber. Finally, we attempted to release and grasp the bead sample using a pair of PLLA fibers like tweezers, and succeeded.

materials science, multidisciplinary,physics, condensed matter

Raman mapping of piezoelectric poly( l -lactic acid) films for force sensors

Hierarchically Structured Hollow PVDF Nanofibers for Flexible Piezoelectric Sensor

Ferroelectric Thin-Film Active Sensors for Structural Health Monitoring

Skin‐Adhesive Flexible Force Sensors Based on Piezoelectric Poly(l‐lactic acid) for Human Behavior Recognition

High piezoelectric performance of poly(lactic acid) film manufactured by solid-state extrusion

Electrospun Environment‐Friendly Poly (L‐Lactic Acid)/CO2‐Based Polyurea Nanofiber Film for Piezoelectric Sensor

Filler-Enhanced Piezoelectricity of Poly-L-Lactide and Its Use as a Functional Ultrasound-Activated Biomaterial

A correlation study on piezo-embedded carbon fibre reinforced polylactic acid composite: Experimental and numerical modelling

High Performance Piezoelectric Polymer Film with Aligned Electroactive Phase Nanofibrils Achieved by Melt Stretching of Slightly Crosslinked Poly(vinylidene Fluoride) for Sensor Applications

Fundamental study on improvement of piezoelectricity of poly(ι-lactic acid) and its application to film actuators

Flexible Piezoelectric Tactile Sensor Array For Dynamic Three-Axis Force Measurement

On the Nanoscale Mapping of the Mechanical and Piezoelectric Properties of Poly (L-Lactic Acid) Electrospun Nanofibers

Piezoelectric Polyacrylonitrile Nanofiber Film-Based Dual-Function Self-Powered Flexible Sensor.

Conjugated Polymer Films for Piezoresistive Stress Sensing

High Performance Piezoelectric Devices Based on Aligned Arrays of Nanofibers of Poly[(vinylidenefluoride-co-trifluoroethylene]

Polylactic Acid Piezo-Biopolymers: Chemistry, Structural Evolution, Fabrication Methods, and Tissue Engineering Applications

Uniaxially drawn poly (L-lactic acid)/ poly (vinylidene fluoride) polymer blend as a promising piezoelectric material: Hysteresis and resonance spectroscopy study

Flexible Piezoelectric 0–3 PZT@C/PDMS Composite Films for Pressure Sensor and Limb Motion Monitoring

Ultrastable piezoelectric biomaterial nanofibers and fabrics as an implantable and conformal electromechanical sensor patch

High-Performance Flexible PLA/BTO-Based Pressure Sensor for Motion Monitoring and Human–Computer Interaction

Microactuators with Piezoelectric Polylactic Acid Fibers—Toward the Realization of Tweezers for Biological Cells