Abstract:This paper presents a comprehensive review of recent studies in electrical power generation from various thermal-consuming processes. In particular, the paper concentrates on TEG technology in recovering waste heat from industrial applications such as chimneys and automotive engines. Studies conclude that TEGs have a lower conversion efficiency (ranging between 5% and 10%), leading to low power output. Also, they state that most of the available TEGs have low operating temperatures limiting their commercial use. Therefore, an effort is taken to understand the key parameters that influence the performance of a thermoelectric generator. It is shown that a large temperature difference across the module, high heat dissipation from the cold side of the TEG and using thermoelectric materials with a high figure of merit generally improve the performance of the thermoelectric generator system. TEG module's cold-side temperature has a large effect on the power output than the hot-side temperature. Several geometric optimization methods, such as flaps and heat spreaders under natural convection resulted in a 129% and 42% increase in TEG power output, respectively. The survey also shows that forced cooling using side-mounted fans produces 58.6% more power compared to the top-mounted fan on the heat sink. However, optimization in fan selection is required to ensure that the power produced by forced cooling is sufficient to run the fans and output higher than the natural convection cooling case. Several studies also show that most of the commercially available TEG modules made from Bismuth telluride suffer from low operating temperature (maximum of 2600C) and have figure of merit of 1.2 maximum and low conversion efficiency (up to 5%). Recommendations are made to further research alternatives like SiGe alloys, clathrates, skutterudites, and complementary metal-oxide semiconductors with better temperature ranges and figures of merit.The carrier transport processes in thermoelectric materials are significantly correlated with the performance of thermoelectric devices (TEs), which is modeled in this study considering the drift-diffusion equation with thermoelectric contributions for detailing the effects of carrier transport on the yielded current density. A micro thermoelectric generator (μTEG) with boron and arsenic being respectively doped into Si0.7Ge0.3 for p-type and n-type thermoelectric materials is employed as the study case by the three-dimensional numerical simulation to reveal the effects of doping concentrations on the thermoelectric performance. Based on the simulation results a novel μTEG design that incorporates PN junctions to extract minority carriers to reduce the recombination rates of electrons and holes is proposed. The performances for conventional and the present novel μTEGs at different temperature differences are compared. The results show that there is an optimal doping concentration for the conventional μTEG to peak the output power and the thermoelectric conversion efficiency. In particular, the novel μTEG reveals a significant improvement of thermoelectric efficiency by approximately 20% as the hot-end temperature is above 900 K. The transport of minority carriers by the PN junctions demonstrates the expected effects through the analysis on the vector distribution of minority carrier current density.Thermal stress plays an important role in the lifetime of thermoelectric generators, and its minimization can prolong the usage of the generators. To figure out and efficiently lower the thermal stress, this study analyzes the thermoelectric performance and thermal stress of a thermoelectric module in a waste heat recovery system. The performance of the TEM with varied numbers of square pin fins in a flow channel is examined by computational fluid dynamics. The results indicate that for different numbers of square pin fins, the heat transfer rate of the module's hot side increases as the number of fins increases. When the number of fins increases from 36 to 84, the heat transfer rate improves by 8.57%. In addition, the temperature distribution in the module in a waste heat recovery system is uneven due to differences in heat transfer. Therefore, the thermal stress of the module is uneven, and the maximum thermal stress occurs in the TE legs, which are located at the corners of the module. To reduce the maximum thermal stress, the thicknesses of the ceramic plate and the thermoelectric legs are optimized using the multi-objective genetic algorithm. The optimization results indicate that the maximum thermal stress of the module is proportional to its output power, meaning that as the maximum thermal stress in the module is minimized, its output power will approach the minimum value. Instead, the same method is employed to minimize the maximum thermal stress on the module while maintaining its output -Abstract Truncated-

Applications of Thermoelectric Generators To Improve Catalytic-Assisted Hydrogen Production Efficiency: Future Directions

Thermoelectric Generation from Exhaust Heat in Electrified Natural Gas Trucks: Modeling and Analysis of an Integrated Engine System Performance Improvement

Energy Harvesting Via Thermoelectric Generators for Green Hydrogen Production: Methods and Techniques

Advancements in Thermoelectric Generator Design: Exploring Heat Exchanger Efficiency and Material Properties

Current and future trend opportunities of thermoelectric generator applications in waste heat recovery

Optimization of Thermoelectric Generator (TEG) Integrated with Three-Way Catalytic Converter (TWC) for Harvesting Engine's Exhaust Waste Heat

Study of Thermoelectric Generator Utilization to Recover Heat at Low Temperature Grade Application: A Review

Economic, thermal analysis and optimizing of a novel hybrid fuel cell and two-stage thermoelectric device for waste heat-recovery applications

Experiments on Waste Heat Thermoelectric Generation for Passenger Vehicles

Performance Analysis and Optimization of a TEG-based Compression Hydrogen Storage Waste Heat Recovery System

Enhanced hydrogen production from thermochemical processes

Distributed electrified heating for efficient hydrogen production

Thermoelectrocatalysis: an emerging strategy for converting waste heat into chemical energy

Emerging electrochemical and membrane-based systems to convert low-grade heat to electricity

Evolution of Thermoelectric Generators: From Application to Hybridization

Comprehensive review in waste heat recovery in different thermal energy-consuming processes using thermoelectric generators for electrical power generation

An energy storage approach for storing surplus power into hydrogen in a cogeneration system

Thermocatalytic Hydrogen Production Through Decomposition of Methane-A Review

Assessment of the integration of Three-Way Catalytic converter and Thermoelectric Generator

Bi2Te3/Carbon Nanotube Hybrid Nanomaterials as Catalysts for Thermoelectric Hydrogen Peroxide Generation

Effect of Convection Heat Transfer on Performance of Waste Heat Thermoelectric Generator